Toshiba BSX5TTS25QMR, B-SX5T-TS22-QM-R, BSX5TTS22QMR manual On Line Mode, Operation Panel

Page 84

3. ON LINE MODE

ENGLISH VERSION EO1-33059

3.1 Operation Panel

3. ON LINE MODE

3.1 Operation Panel

This chapter describes usage of the keys on the Operation Panel in On Line mode.

When the printer is in On Line mode and connected to a host computer, the normal operation of printing images on labels or tags can be accomplished.

•The figure below illustrates the operation panel and key functions.

LCD Message Display

ON LINE LED (Green)

POWER LED ERROR LED (Red)

(Green)

[FEED] key
[RESTART] key	[PAUSE] key
[RESTART] key

NOTE:

Flashes only when the Ribbon Near End Detection function is selected.

NOTE:

Use the [RESTART] key to resume printing after a pause, or after clearing an error.

The LCD Message Display shows messages in alphanumeric characters and symbols to indicate the printer’s current status. Up to 32 characters can be displayed on two lines.

There are three LED lights on the operation panel.

LED	Illuminates when…	Flashes when…
POWER	The printer is turned on.	-----
ON LINE	The printer is ready to	The printer is
	print.	communicating with
		your computer.
ERROR	Any error occurs with	The ribbon is nearly
	the printer.	over. (See NOTE.)

There are three keys on the operation panel.

PAUSE	Used to stop printing temporarily.
RESTART	Used to restart printing.
FEED	Used to feed the media.

E3- 1

Image 84

Contents SX5T Series CE Compliance for EU only VorsichtSX5T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents E5-1 E6-1E7-1 EA1-1Introduction Features Unpacking Product OverviewAccessories ContentsDimensions Front ViewRear View Operation Panel InteriorOptions Option Name Type UsagePrinter Setup Setup FlowProcedure ReferenceInstallation Connecting the Power Cord Fitting the Fan FilterExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Batch mode Strip modeSTANDARD/PEEL OFF position Built-in rewinder mode AdjustmentCut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the PrinterPcmcia Cards How to enter the System Mode Parameter Setting SequentiallyCharacter Code Selection Character Zero SelectionBaud Rate Selection Data Length SelectionStop Bit Selection Parity SelectionFlow Control Code Selection LCD Language Selection Auto Forward Wait SelectionHead Up Cut/Rewinder Selection Feed keySolenoid Type Selection Ribbon Saving Function SelectionControl Code Selection Strip Wait Status Selection Feed Key Function SelectionKanji Code Selection Euro Code SelectionAuto Print Head Check Selection Centronics Interface ACK/BUSY Timing SelectionWeb Printer Function Selection Input Prime SelectionRibbon Near End Selection Expansion I/O Interface Type SelectionCentronics Interface Selection Plug & Play SelectionLabel End/Ribbon End Selection Pre-Strip SelectionMaxi Code Specification Selection Reverse Feed Speed SelectionPrint Head Type Selection Dump Mode Setting DumpedReceive Buffer Size Required Label LengthWhen the Pause key is pressed, Basic program is executed Installing the Printer Drivers IntroductionGeneral Description Installing the Printer Driver Parallel InterfaceWindows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using a Strip Module or an optional Cutter Module Position and Print Tone Fine Adjustment Feed Amount Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentPosition and Print Tone FineExample of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltageTHRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation PanelReset OperationMaintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Possible Problems Possible Problems Causes SolutionsRefer to .1 Media Removing Jammed Media Printer Specifications ModelSX5T-TS22-QM-R Supply Specifications MediaMedia Type LabelDetection Area of the Transmissive Sensor LabelTag paper with square holes Detection Area of the Reflective Sensor Effective Print AreaRfid Tags „ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R„ B-9704-RFID-H1-QM-R Media feed direction Ribbon Recommended Media and Ribbon TypesMedia type Description Care/Handling of Media and Ribbon Ribbon type DescriptionCombination of Media and Ribbon Symbols in the message Appendix 1 Messages and LedsSystem Error Following message appears Appendix 2 Interface Parallel interface Centronics StandardConnector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-U1-US RFID-U1-EURFID-H1-QM Appendix 3 Power Cord When purchasing the power cordAppendix 4 Print Samples Interleaved 2 JAN13, EAN13EAN13+2 digits EAN13+5 digitsUPC-A+5 digits Industrial 2Customer bar code KIX CodeAppendix 5 Glossaries Bar codePrint head element USB Universal Serial BusPower LED IndexIndex EO1-33059

Related manuals

Manual 56 pages 47.42 Kb