Toshiba B-SX5T-TS25-QM-R Position and Print Tone Fine Adjustment, Feed Amount Fine Adjustment

Page 71

2. PRINTER SETUP

ENGLISH VERSION EO1-33059

2.12 Position and Print Tone Fine Adjustment

2.12Position and Print Tone Fine Adjustment

<3>ADJUST SET

[PAUSE]

<3>ADJUST SET FEED ADJ.+10.0mm

[PAUSE]

<3>ADJUST SET CUT ADJ. +10.0mm

[PAUSE]

<3>ADJUST SET BACK ADJ. +5.0mm

[PAUSE]

<3>ADJUST SET

X ADJUST +50.0mm

[PAUSE]

<3>ADJUST SET TONE ADJ.<T> +3

[PAUSE]

<3>ADJUST SET TONE ADJ.<D> -2

[PAUSE]

<3>ADJUST SET RBN ADJ <FW> -10

[PAUSE]

<3>ADJUST SET RBN ADJ <BK> -5

[PAUSE]

<3>ADJUST SET THRESHOLD<R>1.0V

[PAUSE]

<3>ADJUST SET THRESHOLD<T>1.4V

[PAUSE]

This section describes how to fine adjust a print start position, cut/strip position, reverse feed amount, print tone, and ribbon motor torque.

When a fine adjustment is required, such as print start position, print tone, etc, follow the procedure below.

1.Turn on the printer and confirm that “ONLINE” appears on the LCD Message Display.

2.Press the [PAUSE] key to pause the printer.

3.Hold down the [RESTART] key for three seconds until “<1>RESET” is displayed.

4.Press the [FEED] or [RESTART] key until “<3>ADJUST SET” appears on the LCD Message Display.

5.When “<3>ADJUST SET” appears, press the [PAUSE] key to enter the Parameter Fine Adjustment Mode.

The Parameter Fine Adjustment Mode contains the following sub menus. Each time the [PAUSE] key is pressed, the sub menus are displayed sequentially.

(1)Feed Amount Fine Adjustment:

Feed amount to the print start position is fine adjusted.

(2)Cut/Strip Position Fine Adjustment:

Cut position or strip position is fine adjusted.

(3)Reverse Feed Amount Fine Adjustment: Reverse feed amount is fine adjusted.

(4)X-coordinate Fine Adjustment:

X-coordinate of a print position is fine adjusted.

(5)Print Tone Fine Adjustment (Thermal transfer): Print tone is fine adjusted for thermal transfer mode.

(6)Print Tone Fine Adjustment (Thermal direct): Print tone is fine adjusted for thermal direct mode.

(7)Ribbon Motor Drive Voltage Fine Adjustment (Take-up motor):

Drive voltage of the ribbon take-up motor is fine adjusted.

(8)Ribbon Motor Drive Voltage Fine Adjustment (Feed motor) Drive voltage of the ribbon feed motor is fine adjusted.

(9)Threshold Fine Adjustment (Black mark sensor):

Threshold for the black mark sensor is fine adjusted. See Section 2.13.

(10)Threshold Fine Adjustment (Feed gap sensor):

Threshold for the feed gap sensor is fine adjusted. See Section 2.13.

NOTE:

The printer driver’s properties screen also has Parameter Fine Adjustment menu.

E2-57

Page 70 Page 72
Image 71
Page 70 Page 72
Contents SX5T Series Vorsicht CE Compliance for EU onlySX5T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA1-1 E5-1E6-1 E7-1Product Overview Introduction Features UnpackingContents AccessoriesRear View DimensionsFront View Interior Operation PanelOption Name Type Usage OptionsReference Printer SetupSetup Flow ProcedureInstallation Example of US Type Connecting the Power CordFitting the Fan Filter Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position STANDARD/PEEL OFF position Batch modeStrip mode Adjustment Built-in rewinder modeCut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterPcmcia Cards How to enter the System Mode Sequentially Parameter SettingCharacter Zero Selection Character Code SelectionData Length Selection Baud Rate SelectionFlow Control Code Selection Stop Bit SelectionParity Selection Auto Forward Wait Selection LCD Language SelectionFeed key Head Up Cut/Rewinder SelectionRibbon Saving Function Selection Solenoid Type SelectionControl Code Selection Feed Key Function Selection Strip Wait Status SelectionEuro Code Selection Kanji Code SelectionCentronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionInput Prime Selection Web Printer Function SelectionExpansion I/O Interface Type Selection Ribbon Near End SelectionPlug & Play Selection Centronics Interface SelectionPre-Strip Selection Label End/Ribbon End SelectionReverse Feed Speed Selection Maxi Code Specification SelectionPrint Head Type Selection Dumped Dump Mode SettingRequired Label Length Receive Buffer SizeWhen the Pause key is pressed, Basic program is executed General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer DriverWindows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using a Strip Module or an optional Cutter Module Coordinate Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Cut/Strip Position Fine AdjustmentTone Fine Position and PrintExample of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Storing a No Media Level Voltage „ Manual Threshold SettingTHRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line ModeOperation ResetPrint Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter Module Restart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsError Messages Problems/Cause Solutions Possible Problems Causes Solutions Possible ProblemsRefer to .1 Media Removing Jammed Media Model Printer SpecificationsSX5T-TS22-QM-R Label Supply SpecificationsMedia Media TypeTag paper with square holes Detection Area of the Transmissive SensorLabel Effective Print Area Detection Area of the Reflective Sensor„ B-9704-RFID-H1-QM-R Rfid Tags„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Media feed direction Media type Description RibbonRecommended Media and Ribbon Types Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Appendix 1 Messages and Leds Symbols in the messageSystem Error Following message appears Parallel interface Centronics Standard Appendix 2 InterfaceConnector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-H1-QM RFID-U1-USRFID-U1-EU When purchasing the power cord Appendix 3 Power CordAppendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digitsKIX Code UPC-A+5 digitsIndustrial 2 Customer bar codeBar code Appendix 5 GlossariesUSB Universal Serial Bus Print head elementIndex Power LEDIndex EO1-33059
Related manuals
Manual 56 pages 47.42 Kb
Top Page Image Contents