Toshiba BSX5TTS22QMR, BSX5TTS25QMR, B-SX5T-TS22-QM-R manual Parameter Setting, Sequentially

Page 30

2. PRINTER SETUP

ENGLISH VERSION EO1-33059

2.9 Setting an Operating Environment

2.9.1 Parameter Setting	While “<2>PARAMETER SET” is displayed on the LCD Message
	Display, press the [PAUSE] key to enter the Parameter Setting Mode.
	The Parameter Setting Mode contains the following sub menus. Each
	time the [PAUSE] key is pressed, the sub menus are displayed
	sequentially.

(1) Character code selection

(2) Character zero selection

(3) Baud rate selection

(4) Data length selection

(5) Stop bit selection

(6) Parity selection

(7) Flow control code selection

(8) LCD language selection

(9) Auto forward wait selection

(10) Head up cut/Rewinder selection

(11) Solenoid type selection

(12) Ribbon saving function selection

(13) Control code selection

(14) Strip wait status selection

(15) FEED key function selection

(16) KANJI code selection

(17) EURO code selection

(18) Auto print head check selection

(19) Centronics ACK/BUSY timing selection

(20) Web printer function selection

(21) Input prime selection

(22) Ribbon near end selection

(23) Expansion I/O interface selection

(24) Centronics interface selection

(25) Plug & Play selection

(26) Label end/ribbon end selection

(27) Pre-strip selection

(28) Reverse feed speed selection

(29) Maxi code specification selection

(30) Print head type selection

E2-16

Image 30

Contents SX5T Series CE Compliance for EU only VorsichtSX5T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents E7-1 E5-1E6-1 EA1-1Introduction Features Unpacking Product OverviewAccessories ContentsDimensions Front ViewRear View Operation Panel InteriorOptions Option Name Type UsageProcedure Printer SetupSetup Flow ReferenceInstallation Connecting the Power Cord Fitting the Fan FilterExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Batch mode Strip modeSTANDARD/PEEL OFF position Built-in rewinder mode AdjustmentCut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the PrinterPcmcia Cards How to enter the System Mode Parameter Setting SequentiallyCharacter Code Selection Character Zero SelectionBaud Rate Selection Data Length SelectionStop Bit Selection Parity SelectionFlow Control Code Selection LCD Language Selection Auto Forward Wait SelectionHead Up Cut/Rewinder Selection Feed keySolenoid Type Selection Ribbon Saving Function SelectionControl Code Selection Strip Wait Status Selection Feed Key Function SelectionKanji Code Selection Euro Code SelectionAuto Print Head Check Selection Centronics Interface ACK/BUSY Timing SelectionWeb Printer Function Selection Input Prime SelectionRibbon Near End Selection Expansion I/O Interface Type SelectionCentronics Interface Selection Plug & Play SelectionLabel End/Ribbon End Selection Pre-Strip SelectionMaxi Code Specification Selection Reverse Feed Speed SelectionPrint Head Type Selection Dump Mode Setting DumpedReceive Buffer Size Required Label LengthWhen the Pause key is pressed, Basic program is executed Installing the Printer Drivers IntroductionGeneral Description Installing the Printer Driver Parallel InterfaceWindows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using a Strip Module or an optional Cutter Module Cut/Strip Position Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Coordinate Fine AdjustmentPosition and Print Tone FineExample of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltageTHRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation PanelReset OperationMaintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyError Messages Problems/Cause Solutions Possible Problems Possible Problems Causes SolutionsRefer to .1 Media Removing Jammed Media Printer Specifications ModelSX5T-TS22-QM-R Media Type Supply SpecificationsMedia LabelDetection Area of the Transmissive Sensor LabelTag paper with square holes Detection Area of the Reflective Sensor Effective Print AreaRfid Tags „ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R„ B-9704-RFID-H1-QM-R Media feed direction Ribbon Recommended Media and Ribbon TypesMedia type Description Care/Handling of Media and Ribbon Ribbon type DescriptionCombination of Media and Ribbon Symbols in the message Appendix 1 Messages and LedsSystem Error Following message appears Appendix 2 Interface Parallel interface Centronics StandardConnector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-U1-US RFID-U1-EURFID-H1-QM Appendix 3 Power Cord When purchasing the power cordAppendix 4 Print Samples EAN13+2 digits Interleaved 2JAN13, EAN13 EAN13+5 digitsCustomer bar code UPC-A+5 digitsIndustrial 2 KIX CodeAppendix 5 Glossaries Bar codePrint head element USB Universal Serial BusPower LED IndexIndex EO1-33059

Related manuals

Manual 56 pages 47.42 Kb