Toshiba BSX5TTS25QMR, B-SX5T-TS22-QM-R, BSX5TTS22QMR, B-SX5T-TS25-QM-R manual Feed and Pause keys

Page 80

2.PRINTER SETUP

ENGLISH VERSION EO1-33059

2.13 Threshold Setting

2.13Threshold Setting (Cont.)

<5>SENSOR ADJ.

[PAUSE]

<5>SENSOR ADJ. [H]28°C [A]28°C

[PAUSE]

<5>SENSOR ADJ. [REFLECT] 3.5V

[FEED] or [RESTART]

<5>SENSOR ADJ. [REFLECT] 4.8V*

[PAUSE]

<5>SENSOR ADJ. [TRANS.] 2.4V

[FEED] or [RESTART]

<5>SENSOR ADJ. [TRANS.] 4.1V*

[PAUSE]

<5>SENSOR ADJ. [PE]R0.1V T4.8V

[FEED] or [RESTART]

<5>SENSOR ADJ. [PE]R0.1V T4.8V*

[PAUSE]

<5>SENSOR ADJ. [RIBBON] 3.1V

[FEED] or [RESTART]

<5>SENSOR ADJ. [RIBBON] 3.1V*

[PAUSE]

Manual threshold setting procedure

If a paper jam error still occurs even after an automatic threshold setting has been performed, manually set the threshold voltage.

To make a threshold value manually set in this section effective, select the Transmissive Sensor (when using manual threshold value) or Reflective Sensor (when using manual threshold value) within software commands or the printer driver.

1.While holding down the [FEED] and [PAUSE] keys, turn on the printer.

2.When “<1>DIAG.” appears on the LCD Message Display, release the

[FEED] and [PAUSE] keys.

<1>DIAG.

Now, the printer is in the System Mode for system administrators.

3.Press the [FEED] or [RESTART] key until “<5>SENSOR ADJ.” appears on the LCD Message Display.

<5>SENSOR ADJ.

4.Press the [PAUSE] key to enter the Sensor Adjustment Mode.

<5>SENSOR ADJ. [H]28°C [A]28°C

The Sensor Adjustment Mode contains sub menus for displaying the current status of each sensor and for storing “media level” voltage and “no media level” voltage. Each time the [PAUSE] key is pressed, the sub menus are displayed sequentially.

(1)Sensor Status Display:

Temperatures being detected by the Print Head Thermistor and the Ambient Thermistor are displayed.

(2)Black Mark Sensor Status Display:

Voltage being detected by the Black Mark Sensor is displayed.

(3)Black Mark Sensor Adjustment:

Using the media actually used, a “media level” voltage is stored.

(4)Feed Gap Sensor Status Display:

Voltage being detected by the Feed Gap Sensor is displayed.

(5)Feed Gap Sensor Adjustment:

Using the media actually used, a “media level” voltage is stored.

(6)Black Mark Sensor/Feed Gap Sensor Status Display (No media):

“No media level” voltage detected by the Black Mark Sensor/Feed Gap Sensor is displayed.

(7)Black Mark Sensor/Feed Gap Sensor Adjustment (No media):

“No media level” voltage is stored.

(8)Ribbon End Sensor Status Display:

Voltage being detected by the Ribbon End Sensor is displayed.

(9)Ribbon End Sensor Adjustment:

Using the ribbon actually used, a “ribbon level” voltage is stored.

E2-66

Image 80
Contents SX5T Series CE Compliance for EU only VorsichtSX5T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents E5-1 E6-1E7-1 EA1-1Introduction Features Unpacking Product OverviewAccessories ContentsRear View DimensionsFront View Operation Panel InteriorOptions Option Name Type UsagePrinter Setup Setup FlowProcedure ReferenceInstallation Example of US Type Connecting the Power CordFitting the Fan Filter Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position STANDARD/PEEL OFF position Batch modeStrip mode Built-in rewinder mode AdjustmentCut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the PrinterPcmcia Cards How to enter the System Mode Parameter Setting SequentiallyCharacter Code Selection Character Zero SelectionBaud Rate Selection Data Length SelectionFlow Control Code Selection Stop Bit SelectionParity Selection LCD Language Selection Auto Forward Wait SelectionHead Up Cut/Rewinder Selection Feed keySolenoid Type Selection Ribbon Saving Function SelectionControl Code Selection Strip Wait Status Selection Feed Key Function SelectionKanji Code Selection Euro Code SelectionAuto Print Head Check Selection Centronics Interface ACK/BUSY Timing SelectionWeb Printer Function Selection Input Prime SelectionRibbon Near End Selection Expansion I/O Interface Type SelectionCentronics Interface Selection Plug & Play SelectionLabel End/Ribbon End Selection Pre-Strip SelectionMaxi Code Specification Selection Reverse Feed Speed SelectionPrint Head Type Selection Dump Mode Setting DumpedReceive Buffer Size Required Label LengthWhen the Pause key is pressed, Basic program is executed General Description Installing the Printer DriversIntroduction Installing the Printer Driver Parallel InterfaceWindows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using a Strip Module or an optional Cutter Module Position and Print Tone Fine Adjustment Feed Amount Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentPosition and Print Tone FineExample of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltageTHRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation PanelReset OperationPrint Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter Module Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Possible Problems Possible Problems Causes SolutionsRefer to .1 Media Removing Jammed Media Printer Specifications ModelSX5T-TS22-QM-R Supply Specifications MediaMedia Type LabelTag paper with square holes Detection Area of the Transmissive SensorLabel Detection Area of the Reflective Sensor Effective Print Area„ B-9704-RFID-H1-QM-R Rfid Tags„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Media feed direction Media type Description RibbonRecommended Media and Ribbon Types Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Symbols in the message Appendix 1 Messages and LedsSystem Error Following message appears Appendix 2 Interface Parallel interface Centronics StandardConnector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-H1-QM RFID-U1-USRFID-U1-EU Appendix 3 Power Cord When purchasing the power cordAppendix 4 Print Samples Interleaved 2 JAN13, EAN13EAN13+2 digits EAN13+5 digitsUPC-A+5 digits Industrial 2Customer bar code KIX CodeAppendix 5 Glossaries Bar codePrint head element USB Universal Serial BusPower LED IndexIndex EO1-33059
Related manuals
Manual 56 pages 47.42 Kb