Toshiba B-SX5T-TS25-QM-R, BSX5TTS25QMR manual Installing the Printer Driver, Parallel Interface

Page 51

2. PRINTER SETUP

ENGLISH VERSION EO1-33059

2.10 Installing the Printer Drivers

2.10.3 Installing the Printer Driver

The installation procedure differs depending on the interface connected to the printer and the operation system you are using. Please install the printer driver by performing the appropriate procedure.

If the previous version of the printer driver has been installed on your host computer , be sure to uninstall it before you install this printer driver. (Refer to Section 2.10.4 Uninstalling the Printer Driver.)

To print via your network, please install the printer driver by performing the installation procedure for the parallel interface, and also perform the following:

1.In the procedure, select “LPT1” for the port.

2.After installation of the printer driver is completed, add the LAN port by referring to Section 2.10.5 Adding/Deleting a LAN Port, and specify the LAN port.

(1)Parallel Interface

To use the parallel interface, the following settings are required, after installing the printer driver:

For Windows 98/Me:	Open the printer properties. Select the “Details” tab and click on the
	[Spool Settings…] button. The “Spool Settings” dialog box is displayed.
	Select “Disable bi-directional support for this printer”.
For Windows 2000/XP:	Open the printer properties and select the “Ports” tab. Mark off the “Enable
	bidirectional support” checkbox.

NOTE:

In case of the B-SX4T or B-SX5T series, make sure that the Centronics interface type is set to SPP (default).

E2-37

Image 51

Contents SX5T Series Vorsicht CE Compliance for EU onlySX5T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA1-1 E5-1E6-1 E7-1Product Overview Introduction Features UnpackingContents AccessoriesDimensions Front ViewRear View Interior Operation PanelOption Name Type Usage OptionsReference Printer SetupSetup Flow ProcedureInstallation Connecting the Power Cord Fitting the Fan FilterExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Batch mode Strip modeSTANDARD/PEEL OFF position Adjustment Built-in rewinder modeCut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterPcmcia Cards How to enter the System Mode Sequentially Parameter SettingCharacter Zero Selection Character Code SelectionData Length Selection Baud Rate SelectionStop Bit Selection Parity SelectionFlow Control Code Selection Auto Forward Wait Selection LCD Language SelectionFeed key Head Up Cut/Rewinder SelectionRibbon Saving Function Selection Solenoid Type SelectionControl Code Selection Feed Key Function Selection Strip Wait Status SelectionEuro Code Selection Kanji Code SelectionCentronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionInput Prime Selection Web Printer Function SelectionExpansion I/O Interface Type Selection Ribbon Near End SelectionPlug & Play Selection Centronics Interface SelectionPre-Strip Selection Label End/Ribbon End SelectionReverse Feed Speed Selection Maxi Code Specification SelectionPrint Head Type Selection Dumped Dump Mode Setting Required Label Length Receive Buffer SizeWhen the Pause key is pressed, Basic program is executed Installing the Printer Drivers IntroductionGeneral Description Parallel Interface Installing the Printer DriverWindows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using a Strip Module or an optional Cutter Module Coordinate Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Cut/Strip Position Fine AdjustmentTone Fine Position and PrintExample of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Storing a No Media Level Voltage „ Manual Threshold SettingTHRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line ModeOperation ResetMaintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Restart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsError Messages Problems/Cause Solutions Possible Problems Causes Solutions Possible ProblemsRefer to .1 Media Removing Jammed Media Model Printer SpecificationsSX5T-TS22-QM-R Label Supply SpecificationsMedia Media TypeDetection Area of the Transmissive Sensor LabelTag paper with square holes Effective Print Area Detection Area of the Reflective SensorRfid Tags „ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R„ B-9704-RFID-H1-QM-R Media feed direction Ribbon Recommended Media and Ribbon TypesMedia type Description Care/Handling of Media and Ribbon Ribbon type DescriptionCombination of Media and Ribbon Appendix 1 Messages and Leds Symbols in the messageSystem Error Following message appears Parallel interface Centronics Standard Appendix 2 InterfaceConnector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-U1-US RFID-U1-EURFID-H1-QM When purchasing the power cord Appendix 3 Power CordAppendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digitsKIX Code UPC-A+5 digitsIndustrial 2 Customer bar codeBar code Appendix 5 GlossariesUSB Universal Serial Bus Print head elementIndex Power LEDIndex EO1-33059

Related manuals

Manual 56 pages 47.42 Kb