Toshiba B-SX5T-TS25-QM-R, BSX5TTS25QMR, B-SX5T-TS22-QM-R Kanji Code Selection, Euro Code Selection

Page 39

2. PRINTER SETUP

ENGLISH VERSION EO1-33059

2.9 Setting an Operating Environment

2.9.1Parameter Setting (Cont.)

NOTE:

Kanji code selection is not supported by the QM model as the Kanji ROMs are not installed.

(16) KANJI Code Selection

This parameter is to choose a KANJI code.

When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears.

<2>PARAMETER SET KANJI CODE TYPE1

Use the [FEED] or [RESTART] key to select a desired option.

 

 

 

 

 

 

 

Windows code

 

 

 

 

 

 

KANJI CODE TYPE1

 

[RESTART]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[FEED]

 

KANJI CODE TYPE2

Original code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE:

After selecting a Kanji code, press the [PAUSE] key.

(17) EURO Code Selection

This parameter is to choose a Euro code (€).

When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears.

<2>PARAMETER SET EURO CODE B0

Use the [FEED] or [RESTART] key to select a desired option.

Pressing the [FEED] or [RESTART] key causes 1 byte change in the Euro Code value.

[RESTART]

[FEED]

EURO CODE 20

EURO CODE 21

EURO CODE FE

EURO CODE FF

After selecting a Euro code, press the [PAUSE] key.

E2-25

Image 39
Contents SX5T Series Vorsicht CE Compliance for EU onlySX5T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA1-1 E5-1E6-1 E7-1Product Overview Introduction Features UnpackingContents AccessoriesDimensions Front ViewRear View Interior Operation PanelOption Name Type Usage OptionsReference Printer SetupSetup Flow ProcedureInstallation Connecting the Power Cord Fitting the Fan FilterExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Batch mode Strip modeSTANDARD/PEEL OFF position Adjustment Built-in rewinder modeCut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterPcmcia Cards How to enter the System Mode Sequentially Parameter SettingCharacter Zero Selection Character Code SelectionData Length Selection Baud Rate SelectionStop Bit Selection Parity SelectionFlow Control Code Selection Auto Forward Wait Selection LCD Language SelectionFeed key Head Up Cut/Rewinder SelectionRibbon Saving Function Selection Solenoid Type SelectionControl Code Selection Feed Key Function Selection Strip Wait Status SelectionEuro Code Selection Kanji Code SelectionCentronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionInput Prime Selection Web Printer Function SelectionExpansion I/O Interface Type Selection Ribbon Near End SelectionPlug & Play Selection Centronics Interface SelectionPre-Strip Selection Label End/Ribbon End SelectionReverse Feed Speed Selection Maxi Code Specification SelectionPrint Head Type Selection Dumped Dump Mode SettingRequired Label Length Receive Buffer SizeWhen the Pause key is pressed, Basic program is executed Installing the Printer Drivers IntroductionGeneral Description Parallel Interface Installing the Printer DriverWindows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using a Strip Module or an optional Cutter Module Coordinate Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Cut/Strip Position Fine AdjustmentTone Fine Position and PrintExample of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Storing a No Media Level Voltage „ Manual Threshold SettingTHRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line ModeOperation ResetMaintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Restart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsError Messages Problems/Cause Solutions Possible Problems Causes Solutions Possible ProblemsRefer to .1 Media Removing Jammed Media Model Printer SpecificationsSX5T-TS22-QM-R Label Supply SpecificationsMedia Media TypeDetection Area of the Transmissive Sensor LabelTag paper with square holes Effective Print Area Detection Area of the Reflective SensorRfid Tags „ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R„ B-9704-RFID-H1-QM-R Media feed direction Ribbon Recommended Media and Ribbon TypesMedia type Description Care/Handling of Media and Ribbon Ribbon type DescriptionCombination of Media and Ribbon Appendix 1 Messages and Leds Symbols in the messageSystem Error Following message appears Parallel interface Centronics Standard Appendix 2 InterfaceConnector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-U1-US RFID-U1-EURFID-H1-QM When purchasing the power cord Appendix 3 Power CordAppendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digitsKIX Code UPC-A+5 digitsIndustrial 2 Customer bar codeBar code Appendix 5 GlossariesUSB Universal Serial Bus Print head elementIndex Power LEDIndex EO1-33059
Related manuals
Manual 56 pages 47.42 Kb