Toshiba BSX5TTS25QMR, B-SX5T-TS22-QM-R, BSX5TTS22QMR manual Auto Print Head Check Selection

Page 40

2. PRINTER SETUP

ENGLISH VERSION EO1-33059

2.9 Setting an Operating Environment

2.9.1Parameter Setting (Cont.)

NOTES:

1. It takes about 2 seconds to perform an Auto Print Head check.

2.It is recommended that this function should be activated when high quality printing such as bar codes printing is required. Otherwise, choose OFF.

3.When a broken element is found, the printer stops, displaying “HEAD ERROR”. The error state can be cleared by pressing the [RESTART] key, but if the broken element affects bar code readability or actual operations, please replace the print head with a proper one.

(18) Auto Print Head Check Selection

This parameter is to choose whether to perform the Auto Print Head Check function at the power on time. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears.

<2>PARAMETER SET AUTO HD CHK OFF

Use the [FEED] or [RESTART] key to select a desired option.

 

 

 

 

 

 

AUTO HD CHK OFF

 

 

 

 

 

 

 

 

 

[RESTART]

 

 

 

Auto print head broken element

 

 

 

 

 

 

 

 

 

 

 

 

check is not performed.

 

 

[FEED]

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO HD CHK ON

 

 

 

 

 

 

 

 

 

Auto print head broken element check is performed.

After selecting auto print head check, press the [PAUSE] key.

(19) Centronics Interface ACK/BUSY Timing Selection

This parameter is to choose an ACK/BUSY timing of the Centronics interface.

“TYPE1” has been chosen as default, but if a communication error occurs or a communication is not properly made, change to “TYPE2”.

When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears”.

<2>PARAMETER SET ACK/BUSY TYPE1

Use the [FEED] or [RESTART] key to select a desired option.

 

 

 

 

 

 

ACK/BUSY TYPE1

 

 

 

 

 

 

 

 

 

[RESTART]

 

 

and a release of

A rise of ACK signal

 

 

 

 

 

 

BUSY occur at the same time.

 

 

[FEED]

 

 

 

 

 

 

 

 

 

 

 

 

 

ACK/BUSY TYPE2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A fall of ACK signal and a release of

BUSY occur at the same time.

After selecting an ACK/BUSY timing, press the [PAUSE] key.

E2-26

Image 40
Contents SX5T Series CE Compliance for EU only VorsichtSX5T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents E5-1 E6-1E7-1 EA1-1Introduction Features Unpacking Product OverviewAccessories ContentsFront View DimensionsRear View Operation Panel InteriorOptions Option Name Type UsagePrinter Setup Setup FlowProcedure ReferenceInstallation Fitting the Fan Filter Connecting the Power CordExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Strip mode Batch modeSTANDARD/PEEL OFF position Built-in rewinder mode AdjustmentCut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the PrinterPcmcia Cards How to enter the System Mode Parameter Setting SequentiallyCharacter Code Selection Character Zero SelectionBaud Rate Selection Data Length SelectionParity Selection Stop Bit SelectionFlow Control Code Selection LCD Language Selection Auto Forward Wait SelectionHead Up Cut/Rewinder Selection Feed keySolenoid Type Selection Ribbon Saving Function SelectionControl Code Selection Strip Wait Status Selection Feed Key Function SelectionKanji Code Selection Euro Code SelectionAuto Print Head Check Selection Centronics Interface ACK/BUSY Timing SelectionWeb Printer Function Selection Input Prime SelectionRibbon Near End Selection Expansion I/O Interface Type SelectionCentronics Interface Selection Plug & Play SelectionLabel End/Ribbon End Selection Pre-Strip SelectionMaxi Code Specification Selection Reverse Feed Speed SelectionPrint Head Type Selection Dump Mode Setting DumpedReceive Buffer Size Required Label LengthWhen the Pause key is pressed, Basic program is executed Introduction Installing the Printer DriversGeneral Description Installing the Printer Driver Parallel InterfaceWindows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using a Strip Module or an optional Cutter Module Position and Print Tone Fine Adjustment Feed Amount Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentPosition and Print Tone FineExample of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltageTHRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation PanelReset OperationCleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Possible Problems Possible Problems Causes SolutionsRefer to .1 Media Removing Jammed Media Printer Specifications ModelSX5T-TS22-QM-R Supply Specifications MediaMedia Type LabelLabel Detection Area of the Transmissive SensorTag paper with square holes Detection Area of the Reflective Sensor Effective Print Area„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Rfid Tags„ B-9704-RFID-H1-QM-R Media feed direction Recommended Media and Ribbon Types RibbonMedia type Description Ribbon type Description Care/Handling of Media and RibbonCombination of Media and Ribbon Symbols in the message Appendix 1 Messages and LedsSystem Error Following message appears Appendix 2 Interface Parallel interface Centronics StandardConnector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-U1-EU RFID-U1-USRFID-H1-QM Appendix 3 Power Cord When purchasing the power cordAppendix 4 Print Samples Interleaved 2 JAN13, EAN13EAN13+2 digits EAN13+5 digitsUPC-A+5 digits Industrial 2Customer bar code KIX CodeAppendix 5 Glossaries Bar codePrint head element USB Universal Serial BusPower LED IndexIndex EO1-33059
Related manuals
Manual 56 pages 47.42 Kb