Toshiba BSX5TTS22QMR, BSX5TTS25QMR, B-SX5T-TS22-QM-R manual Options, Option Name Type Usage

Page 14

1. PRODUCT OVERVIEW

ENGLISH VERSION EO1-33059

1.6 Options

1.6 Options

Option Name	Type	Usage
Swing cutter	B-4205-QM-R	A stop and cut swing cutter.
module
Rotary cutter	B-8204-QM-R	Rotary cutter
module
PCMCIA	B-9700-PCM-QM-R	This board enables the use of the following PCMCIA cards.
interface board		ATA card: Conforming to PC card ATA standard
		Flash memory card: 1MB and 4MB cards (See Section 2.8.)
Built-in LAN	B-9700-LAN-QM-R	This board enables the printer to be used in a LAN network.
interface board
USB interface	B-9700-USB-QM-R	Installing this board enables a connection to a PC which has a
board		USB interface.
RFID module	B-9704-RFID-U1-US-R	Installing this module enables read and write of RFID tags.
	B-9704-RFID-U1-EU-R	Applicable frequency range differs depending on the module
	B-9704-RFID-H1-QM-R	types:
		U1-US: UHF, 902MHz to 928MHz
		U1-EU: UHF, 869.5MHz
		H1-QM: HF, 13.56MHz
Fanfold paper	B-4905-FF-QM-R	This is a paper guide exclusively used for fanfold paper.
guide module
Wireless LAN	B-9700-WLAN-QM-R	Installing this PC board allows a communication by wireless
board		LAN.

NOTE:

To purchase the optional kits, please contact the nearest authorised TOSHIBA TEC representative or TOSHIBA TEC Head Quarters.

E1- 5

Image 14

Contents SX5T Series CE Compliance for EU only VorsichtSX5T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents E7-1 E5-1E6-1 EA1-1Introduction Features Unpacking Product OverviewAccessories ContentsRear View DimensionsFront View Operation Panel InteriorOptions Option Name Type UsageProcedure Printer SetupSetup Flow ReferenceInstallation Example of US Type Connecting the Power CordFitting the Fan Filter Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position STANDARD/PEEL OFF position Batch modeStrip mode Built-in rewinder mode AdjustmentCut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the PrinterPcmcia Cards How to enter the System Mode Parameter Setting SequentiallyCharacter Code Selection Character Zero SelectionBaud Rate Selection Data Length SelectionFlow Control Code Selection Stop Bit SelectionParity Selection LCD Language Selection Auto Forward Wait SelectionHead Up Cut/Rewinder Selection Feed keySolenoid Type Selection Ribbon Saving Function SelectionControl Code Selection Strip Wait Status Selection Feed Key Function SelectionKanji Code Selection Euro Code SelectionAuto Print Head Check Selection Centronics Interface ACK/BUSY Timing SelectionWeb Printer Function Selection Input Prime SelectionRibbon Near End Selection Expansion I/O Interface Type SelectionCentronics Interface Selection Plug & Play SelectionLabel End/Ribbon End Selection Pre-Strip SelectionMaxi Code Specification Selection Reverse Feed Speed SelectionPrint Head Type Selection Dump Mode Setting DumpedReceive Buffer Size Required Label LengthWhen the Pause key is pressed, Basic program is executed General Description Installing the Printer DriversIntroduction Installing the Printer Driver Parallel InterfaceWindows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using a Strip Module or an optional Cutter Module Cut/Strip Position Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Coordinate Fine AdjustmentPosition and Print Tone FineExample of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltageTHRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation PanelReset OperationPrint Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter Module Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyError Messages Problems/Cause Solutions Possible Problems Possible Problems Causes SolutionsRefer to .1 Media Removing Jammed Media Printer Specifications ModelSX5T-TS22-QM-R Media Type Supply SpecificationsMedia LabelTag paper with square holes Detection Area of the Transmissive SensorLabel Detection Area of the Reflective Sensor Effective Print Area„ B-9704-RFID-H1-QM-R Rfid Tags„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Media feed direction Media type Description RibbonRecommended Media and Ribbon Types Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Symbols in the message Appendix 1 Messages and LedsSystem Error Following message appears Appendix 2 Interface Parallel interface Centronics StandardConnector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-H1-QM RFID-U1-USRFID-U1-EU Appendix 3 Power Cord When purchasing the power cordAppendix 4 Print Samples EAN13+2 digits Interleaved 2JAN13, EAN13 EAN13+5 digitsCustomer bar code UPC-A+5 digitsIndustrial 2 KIX CodeAppendix 5 Glossaries Bar codePrint head element USB Universal Serial BusPower LED IndexIndex EO1-33059

Related manuals

Manual 56 pages 47.42 Kb