Toshiba BSX5TTS25QMR, B-SX5T-TS22-QM-R, BSX5TTS22QMR, B-SX5T-TS25-QM-R manual Optional Cutter Module

Page 88

4. MAINTENANCE

ENGLISH VERSION EO1-33059

4.1 Cleaning

4.1.3 Optional Cutter Module

WARNING!

1.Be sure to turn the power off before cleaning the Cutter Module.

2.As the cutter blade is sharp, care should be taken not to injure yourself when cleaning.

The swing cutter and rotary cutter are available as an option. They are both cleaned in the same way. When removing the Cutter Cover of the rotary cutter unit, remove the screws from the bottom of the cover.

1.Loosen the two screws to remove the Cutter Cover.

2.Remove the Plastic Head Screw to detach the Media Guide.

3.Remove the jammed paper.

4.Clean the Cutter with a soft cloth slightly moistened with alcohol.

5.Reassemble the Cutter Module in the reverse order of removal.

Screw

Plastic Head

Screw

Cutter Unit

Cutter Cover

Media Guide

Fixed Cutter Swing Cutter

E4- 3

Image 88
Contents SX5T Series CE Compliance for EU only VorsichtSX5T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents E5-1 E6-1E7-1 EA1-1Introduction Features Unpacking Product OverviewAccessories ContentsFront View DimensionsRear View Operation Panel InteriorOptions Option Name Type UsagePrinter Setup Setup FlowProcedure ReferenceInstallation Fitting the Fan Filter Connecting the Power CordExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Strip mode Batch modeSTANDARD/PEEL OFF position Built-in rewinder mode AdjustmentCut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the PrinterPcmcia Cards How to enter the System Mode Parameter Setting SequentiallyCharacter Code Selection Character Zero SelectionBaud Rate Selection Data Length SelectionParity Selection Stop Bit SelectionFlow Control Code Selection LCD Language Selection Auto Forward Wait SelectionHead Up Cut/Rewinder Selection Feed keySolenoid Type Selection Ribbon Saving Function SelectionControl Code Selection Strip Wait Status Selection Feed Key Function SelectionKanji Code Selection Euro Code SelectionAuto Print Head Check Selection Centronics Interface ACK/BUSY Timing SelectionWeb Printer Function Selection Input Prime SelectionRibbon Near End Selection Expansion I/O Interface Type SelectionCentronics Interface Selection Plug & Play SelectionLabel End/Ribbon End Selection Pre-Strip SelectionMaxi Code Specification Selection Reverse Feed Speed SelectionPrint Head Type Selection Dump Mode Setting DumpedReceive Buffer Size Required Label LengthWhen the Pause key is pressed, Basic program is executed Introduction Installing the Printer DriversGeneral Description Installing the Printer Driver Parallel InterfaceWindows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using a Strip Module or an optional Cutter Module Position and Print Tone Fine Adjustment Feed Amount Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentPosition and Print Tone FineExample of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltageTHRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation PanelReset OperationCleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Possible Problems Possible Problems Causes SolutionsRefer to .1 Media Removing Jammed Media Printer Specifications ModelSX5T-TS22-QM-R Supply Specifications MediaMedia Type LabelLabel Detection Area of the Transmissive SensorTag paper with square holes Detection Area of the Reflective Sensor Effective Print Area„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Rfid Tags„ B-9704-RFID-H1-QM-R Media feed direction Recommended Media and Ribbon Types RibbonMedia type Description Ribbon type Description Care/Handling of Media and RibbonCombination of Media and Ribbon Symbols in the message Appendix 1 Messages and LedsSystem Error Following message appears Appendix 2 Interface Parallel interface Centronics StandardConnector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-U1-EU RFID-U1-USRFID-H1-QM Appendix 3 Power Cord When purchasing the power cordAppendix 4 Print Samples Interleaved 2 JAN13, EAN13EAN13+2 digits EAN13+5 digitsUPC-A+5 digits Industrial 2Customer bar code KIX CodeAppendix 5 Glossaries Bar codePrint head element USB Universal Serial BusPower LED IndexIndex EO1-33059
Related manuals
Manual 56 pages 47.42 Kb