Toshiba B-SX5T-TS22-QM-R, BSX5TTS25QMR manual Web Printer Function Selection, Input Prime Selection

Page 41

2. PRINTER SETUP

ENGLISH VERSION EO1-33059

2.9 Setting an Operating Environment

2.9.1Parameter Setting (Cont.)

NOTE:

When “WEB PRINTER ON” is selected, the status of the printer connected in a network can be checked through the Web browser.

(20) Web Printer Function Selection

This parameter is to choose whether to use the printer as a web printer. When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears.

<2>PARAMETER SET WEB PRINTER OFF

Use the [FEED] or [RESTART] key to select a desired option.

							Unavailable

	[RESTART]					WEB PRINTER OFF

		[FEED]					Available
		[FEED]				WEB PRINTER ON	Available

After selecting the Web printer function, press the [PAUSE] key.

(21) Input Prime Selection

This parameter is to choose whether to enable a reset operation when INIT signal is ON.

Normally, when the printer receives a reset request signal (nInit signal) from the host via Centronics interface, the printer will be reset and turn to the idle state.

When the INPUT PRIME parameter is set to OFF, the printer is reset but does not turn to idle.

When this parameter is set to ON, the host sends an INIT signal and the printer turns to idle each time the printer is turned on. If you would like to avoid this processing, set this parameter to OFF.

When “<2>PARAMETER SET” appears, press the [PAUSE] key until the following display appears.

<2>PARAMETER SET INPUT PRIME ON

Use the [FEED] or [RESTART] key to select a desired option.


	[RESTART]					INPUT PRIME	ON	Available

		[FEED]						Unavailable
		[FEED]				INPUT PRIME	OFF	Unavailable

After selecting the Input Prime, press the [PAUSE] key.

E2-27

Image 41

Contents SX5T Series Vorsicht CE Compliance for EU onlySX5T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents E6-1 E5-1E7-1 EA1-1Product Overview Introduction Features UnpackingContents AccessoriesRear View DimensionsFront View Interior Operation PanelOption Name Type Usage OptionsSetup Flow Printer SetupProcedure ReferenceInstallation Example of US Type Connecting the Power CordFitting the Fan Filter Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position STANDARD/PEEL OFF position Batch modeStrip mode Adjustment Built-in rewinder modeCut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterPcmcia Cards How to enter the System Mode Sequentially Parameter SettingCharacter Zero Selection Character Code SelectionData Length Selection Baud Rate SelectionFlow Control Code Selection Stop Bit SelectionParity Selection Auto Forward Wait Selection LCD Language SelectionFeed key Head Up Cut/Rewinder SelectionRibbon Saving Function Selection Solenoid Type SelectionControl Code Selection Feed Key Function Selection Strip Wait Status SelectionEuro Code Selection Kanji Code SelectionCentronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionInput Prime Selection Web Printer Function SelectionExpansion I/O Interface Type Selection Ribbon Near End SelectionPlug & Play Selection Centronics Interface SelectionPre-Strip Selection Label End/Ribbon End SelectionReverse Feed Speed Selection Maxi Code Specification SelectionPrint Head Type Selection Dumped Dump Mode SettingRequired Label Length Receive Buffer SizeWhen the Pause key is pressed, Basic program is executed General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer DriverWindows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using a Strip Module or an optional Cutter Module Feed Amount Fine Adjustment Position and Print Tone Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentTone Fine Position and PrintExample of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Storing a No Media Level Voltage „ Manual Threshold SettingTHRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line ModeOperation ResetPrint Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter Module Error Messages TroubleshootingError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Possible Problems Causes Solutions Possible ProblemsRefer to .1 Media Removing Jammed Media Model Printer SpecificationsSX5T-TS22-QM-R Media Supply SpecificationsMedia Type LabelTag paper with square holes Detection Area of the Transmissive SensorLabel Effective Print Area Detection Area of the Reflective Sensor„ B-9704-RFID-H1-QM-R Rfid Tags„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Media feed direction Media type Description RibbonRecommended Media and Ribbon Types Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Appendix 1 Messages and Leds Symbols in the messageSystem Error Following message appears Parallel interface Centronics Standard Appendix 2 InterfaceConnector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-H1-QM RFID-U1-USRFID-U1-EU When purchasing the power cord Appendix 3 Power CordAppendix 4 Print Samples JAN13, EAN13 Interleaved 2EAN13+2 digits EAN13+5 digitsIndustrial 2 UPC-A+5 digitsCustomer bar code KIX CodeBar code Appendix 5 GlossariesUSB Universal Serial Bus Print head elementIndex Power LEDIndex EO1-33059

Related manuals

Manual 56 pages 47.42 Kb