Toshiba B-SX5T-TS22-QM-R, BSX5TTS25QMR, BSX5TTS22QMR, B-SX5T-TS25-QM-R How to enter the System Mode

Page 29

2. PRINTER SETUP

ENGLISH VERSION EO1-33059

2.9 Setting an Operating Environment

2.9Setting an Operating Environment

LCD Message

Display

FEED key

RESTART key

PAUSE key

ON LINE

[PAUSE]

PAUSE

Hold down [RESTART] for 3 sec.

<1>RESET

[FEED] [RESTART]

<2>PARAMETER SET

[FEED] [RESTART]

<3>ADJUST SET

[FEED] [RESTART]

<4>DUMP MODE

[FEED] [RESTART]

<5>EXPAND MODE

[FEED] [RESTART]

Depending on the settings of your host computer or an interface to be used, it may be necessary to change the printer parameter settings.

Follow the procedures described below to change the printer parameter settings in the System Mode to correspond to your environment.

NOTE:

Incorrect settings can cause the printer to function erroneously. If you have any problems with the parameter settings, please contact your nearest TOSHIBA TEC service representative.

For the settings this manual does not cover, please contact your nearest TOSHIBA TEC service representative, or refer to the B-SX4T/SX5T Series Key Operation Specification stored in the CD-ROM.

How to enter the System Mode

1.Turn on the printer and confirm that “ONLINE” appears on the LCD Message Display.

2.Press the [PAUSE] key to pause the printer.

3.Hold down the [RESTART] key for three seconds until “<1>RESET” is displayed.

The System Mode consists of the following menus.

<1>RESET	This menu is used to clear print data sent from a
	PC and return the printer to an idle state.
	Refer to Section 3.3 Reset.
<2>PARAMETER SET	This menu is used to set the printer parameters.
	Refer to Section 2.9.1 Parameter Setting .
<3>ADJUST SET	This menu is used to make a fine adjustment of a
	print start position, cut position, etc.
	Refer to Section 2.12 Position and Print Tone
	Fine Adjustment.
<4>DUMP MODE	This menu is used to print the data in the receive
	buffer for debug.
	Refer to Section 2.9.2 Dump Mode Setting.
<5>EXPAND MODE	This menu is used to start the program for
	BASIC mode.
	Refer to Section 2.9.3 BASIC Expansion
	Mode .
	NOTES:

1.System Mode menus can be selected with the [RESTART] or [FEED] key.

2.To enter each of the above System Mode menus, press the [PAUSE] key when the menu is displayed.

3.If the [PAUSE] key is pressed with “<1>RESET” being displayed, the printer will turn to an idle state and the message will change to “ONLINE”.

E2-15

Image 29

Contents SX5T Series Vorsicht CE Compliance for EU onlySX5T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents E6-1 E5-1E7-1 EA1-1Product Overview Introduction Features UnpackingContents AccessoriesRear View DimensionsFront View Interior Operation PanelOption Name Type Usage OptionsSetup Flow Printer SetupProcedure ReferenceInstallation Example of US Type Connecting the Power CordFitting the Fan Filter Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position STANDARD/PEEL OFF position Batch modeStrip mode Adjustment Built-in rewinder modeCut mode Option Loading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterPcmcia Cards How to enter the System Mode Sequentially Parameter SettingCharacter Zero Selection Character Code SelectionData Length Selection Baud Rate SelectionFlow Control Code Selection Stop Bit SelectionParity Selection Auto Forward Wait Selection LCD Language SelectionFeed key Head Up Cut/Rewinder SelectionRibbon Saving Function Selection Solenoid Type SelectionControl Code Selection Feed Key Function Selection Strip Wait Status SelectionEuro Code Selection Kanji Code SelectionCentronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionInput Prime Selection Web Printer Function SelectionExpansion I/O Interface Type Selection Ribbon Near End SelectionPlug & Play Selection Centronics Interface SelectionPre-Strip Selection Label End/Ribbon End SelectionReverse Feed Speed Selection Maxi Code Specification SelectionPrint Head Type Selection Dumped Dump Mode SettingRequired Label Length Receive Buffer SizeWhen the Pause key is pressed, Basic program is executed General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer DriverWindows 98/Me E2-39 Windows 2000/XP E2-41 USB Interface E2-43 E2-44 E2-45 Finish button E2-47 E2-48 E2-49 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using a Strip Module or an optional Cutter Module Feed Amount Fine Adjustment Position and Print Tone Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentTone Fine Position and PrintExample of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm Position and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Feed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Storing a No Media Level Voltage „ Manual Threshold SettingTHRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line ModeOperation ResetPrint Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter Module Error Messages TroubleshootingError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Possible Problems Causes Solutions Possible ProblemsRefer to .1 Media Removing Jammed Media Model Printer SpecificationsSX5T-TS22-QM-R Media Supply SpecificationsMedia Type LabelTag paper with square holes Detection Area of the Transmissive SensorLabel Effective Print Area Detection Area of the Reflective Sensor„ B-9704-RFID-H1-QM-R Rfid Tags„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Media feed direction Media type Description RibbonRecommended Media and Ribbon Types Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Appendix 1 Messages and Leds Symbols in the messageSystem Error Following message appears Parallel interface Centronics Standard Appendix 2 InterfaceConnector Serial interface Standard LAN Option B-9700-LAN-QM-R Expansion I/O Interface Option B-7704-IO- QM-R RFID-H1-QM RFID-U1-USRFID-U1-EU When purchasing the power cord Appendix 3 Power CordAppendix 4 Print Samples JAN13, EAN13 Interleaved 2EAN13+2 digits EAN13+5 digitsIndustrial 2 UPC-A+5 digitsCustomer bar code KIX CodeBar code Appendix 5 GlossariesUSB Universal Serial Bus Print head elementIndex Power LEDIndex EO1-33059

Related manuals

Manual 56 pages 47.42 Kb