ADTRAN TA 544 user manual Ethernet Menu

Page 33

TA 544 User Manual/61200704L1-1A

Page 33 of 68

The following selections are possible:

PAP, CHAP OR The TA 544 will ask for EAP during the first PPP

EAP (DEF) LCP negotiation and allow the PPP peer to negotiate down to CHAP or PAP.

CHAP OR EAP The TA 544 will ask for EAP during the first PPP LCP negotiation and allow the PPP peer to negotiate down to CHAP but not PAP.

EAP ONLY The TA 544 will only allow EAP to be negotiated. If the PPP peer is not capable of doing EAP, then the connection will not succeed.

PAP ONLY The TA 544 will only allow PAP to be negotiated. If the PPP peer is not capable of doing PAP, then the connection will not succeed.

> Ethernet

Use the ETHERNET menu (Figure 11) to configure the Ethernet port on the TA 544.

Figure 11. Ethernet Menu

IP

This is used to setup the IP addresses for the LAN on the TA 544.

IP Address

The IP address assigned to the TA 544's Ethernet port is set here. This address must be unique within the network.

Subnet Mask

This is the IP network mask that is to be applied to the TA 544's Ethernet port.

Default Gateway

The default gateway is used by the TA 544 to send IP packets whose destination address is not found in the route table.

© 2001, ADTRAN, Inc.

TA 544 User Manual

Image 33

Contents 1200704L1 4200704L3 To the Holder of the Manual TrademarksSafety Instructions Limited Product Warranty USA International Contact Information2001, ADTRAN, Inc Presales Inquiries and Applications Support Customer Service, Product Support Information, and TrainingPost-Sale Support Repair and ReturnTraining 800 615-1176, ext TrainingContents 2001, ADTRAN, Inc Figures 2001, ADTRAN, Inc Terminal Menu Firmware UpdatesVoice Over DSL Application Mount the Unit Unpack and Inspect the UnitSystem Info Part Number Bootcode RevisionSerial Number Firmware RevisionOperating Mode System ConfigNetwork Timing Mode Telnet AccessSnmp Menu Password Protect Instructions for Changing Passwords Step ActionMaint Port Menu Network Time System Utility Upgrade FirmwareConfig Transfer Ping ATM Config Configuring WAN SettingsDslam Type Layer One InterfaceData Scrambling ATM StatsAP Rx Cells AP Receive Cell ErrorsAP Rx OAM Cells AP Receive Cells DiscardedDSL Rate Config Global Configuring the Router Configuration Use this menu to enter static routes to other networks Bridge Security Ethernet Menu EthernetMAC Address WAN This is the network mask used for this interface Use this menu to configure IP settings When set to Y ES, only IP RIP updates are sent All incoming packets from the WAN are not Session Configuring the Router StatusARP cache Bridge TableConfiguring the Router Logs Wrap Network LogView ClearCall Control Configuring Voice Support ConfigGateway Stats Configuring Voice Support StatusPVC Stats Voice StatsModules Table Managing the Modules ModulesManaging the Modules V.35 Setup ConfigurationMode Following settings are used for FRF5 Following settings are used for FRF8 Network Interface Appendix A. Specifications and FeaturesATM Support Isdn InterfacesPower Security FeaturesManagement Options Serial DataAppendix B. Updating TA 544 Firmware using Xmodem Updating Firmware via a Forced DownloadPress Enter until a menu appears Updating Firmware via the Console Menus 2001, ADTRAN, Inc Appendix C. Updating TA 544 Firmware using Tftp Message Meaning Message Meaning Status Bar Ode Avigation H elp Enu Path Left PaneRight Window Pane Notation Window Pane NavigationNavigating Using the Keyboard Keys Additional Terminal Menu Window FeaturesSession Management Keystrokes Getting Help Application Diagram Voice Turn Up Step Action Appendix F. RFC1483 Quick Start IP Routing WAN Options Appendix G. RFC1483 Quick Start IP Routing with NATBridging Step Action Appendix H. RFC1483 Quick Start BridgingAppendix I. PPPoA Quick Start Guide