ADTRAN TA 544 user manual 2001, ADTRAN, Inc

Page 53

TA 544 User Manual/61200704L1-1A

Page 53 of 68

3.Select XMODEM for TRANSFER METHOD.

4.Press Enter on START TRANSFER <+>.

5.When prompted, press Y to erase flash.

When TA 544 is ready to receive the XMODEM upload, the menu screen will clear and display Transmit Flash . . . download file now. If this does not appear, please review the steps above for possible configuration errors.

6.From the terminal emulation software, begin the XMODEM upload by using the appropriate command sequence. (If necessary, refer to terminal emulation software documentation for help. Also, when specifying the filename, ensure that the file transferred is the one pro- vided by ADTRAN. Otherwise, the update will not complete successfully.)

Because XMODEM data is being transferred in-band through the menu interface, the VT 100 menus of TA 544 will be inoperable from the CRAFT port.

7.When the update has successfully completed, TRANSFER COMPLETE displays in TRANSFER

STATUS. The module restarts immediately and resumes operation. If an error occurs during the update, an error message will display in the TRANSFER STATUS field. If this occurs, return to Step 3 and attempt the update again. If the same error occurs, contact ADTRAN Techni- cal Support.

© 2001, ADTRAN, Inc.

TA 544 User Manual

Image 53

Contents 1200704L1 4200704L3 To the Holder of the Manual TrademarksSafety Instructions Limited Product Warranty USA International Contact Information2001, ADTRAN, Inc Presales Inquiries and Applications Support Customer Service, Product Support Information, and TrainingPost-Sale Support Repair and ReturnTraining 800 615-1176, ext TrainingContents 2001, ADTRAN, Inc Figures 2001, ADTRAN, Inc Terminal Menu Firmware UpdatesVoice Over DSL Application Mount the Unit Unpack and Inspect the UnitSystem Info Part Number Bootcode RevisionSerial Number Firmware RevisionOperating Mode System ConfigNetwork Timing Mode Telnet AccessSnmp Menu Maint Port Menu Password ProtectInstructions for Changing Passwords Step Action Network Time System Utility Upgrade FirmwareConfig Transfer Ping ATM Config Configuring WAN SettingsDslam Type Layer One InterfaceData Scrambling ATM StatsAP Rx Cells AP Receive Cell ErrorsAP Rx OAM Cells AP Receive Cells DiscardedDSL Rate Config Global Configuring the Router ConfigurationUse this menu to enter static routes to other networks Bridge Security Ethernet Menu EthernetMAC Address WAN This is the network mask used for this interface Use this menu to configure IP settings When set to Y ES, only IP RIP updates are sent All incoming packets from the WAN are not Session Configuring the Router StatusARP cache Bridge TableConfiguring the Router Logs Wrap Network LogView ClearCall Control Configuring Voice Support ConfigGateway Stats Configuring Voice Support StatusPVC Stats Voice StatsModules Table Managing the Modules ModulesMode Managing the Modules V.35 SetupConfiguration Following settings are used for FRF5 Following settings are used for FRF8 Network Interface Appendix A. Specifications and FeaturesATM Support Isdn InterfacesPower Security FeaturesManagement Options Serial DataPress Enter until a menu appears Appendix B. Updating TA 544 Firmware using XmodemUpdating Firmware via a Forced Download Updating Firmware via the Console Menus 2001, ADTRAN, Inc Appendix C. Updating TA 544 Firmware using Tftp Message Meaning Message Meaning Status Bar Ode Avigation H elp Enu Path Left PaneRight Window Pane Notation Window Pane NavigationNavigating Using the Keyboard Keys Additional Terminal Menu Window FeaturesSession Management Keystrokes Getting Help Application Diagram Voice Turn Up Step Action Appendix F. RFC1483 Quick Start IP Routing WAN Options Appendix G. RFC1483 Quick Start IP Routing with NATBridging Step Action Appendix H. RFC1483 Quick Start BridgingAppendix I. PPPoA Quick Start Guide