ADTRAN TA 544 user manual Following settings are used for FRF8

Page 48

TA 544 User Manual/61200704L1-1A Page 48 of 68

The following settings are used for FRF8.

LAN FR MAINT PROTOCOL

LAN FR POLL TIMEOUT

T392 (5-30)

FR/ATM PVC MAPPING FR DLCI

ATM VPI

ATM VCI

TRANSLATE

DE MAP

FECN MAP

Frame Relay maintenance or signaling protocol between local V.35 port and the attached DTE port, support ANSI Annex A, CCITT Q933 An- nex D, CISCO LMI or Static (no signaling).

T392 for signaling protocol, typical value 15. No meaning if Maint Protocol is Static.

Up to 4 mappings are supported.

Frame Relay DLCI on V.35 port.

Specifies the virtual path to which DLCI is mapped.

Specifies the virtual circuit to which DLCI is mapped.

Translate or transparent mode between Frame Relay frames and ATM cells.

Map Frame Relay DE bit to ATM CLPI bit, Always 0, Always 1 or Convert each other.

Map Frame Relay FECN bit toATM EFCI bit, Always 0, Always 1 or Convert each other.

TA 544 User Manual

© 2001, ADTRAN, Inc.

Image 48

Contents 1200704L1 4200704L3 Trademarks To the Holder of the ManualSafety Instructions Limited Product Warranty International Contact Information USA2001, ADTRAN, Inc Customer Service, Product Support Information, and Training Presales Inquiries and Applications SupportPost-Sale Support Repair and ReturnTraining Training 800 615-1176, extContents 2001, ADTRAN, Inc Figures 2001, ADTRAN, Inc Firmware Updates Terminal MenuVoice Over DSL Application Unpack and Inspect the Unit Mount the UnitSystem Info Bootcode Revision Part NumberSerial Number Firmware RevisionSystem Config Operating ModeNetwork Timing Mode Telnet AccessSnmp Menu Password Protect Instructions for Changing Passwords Step ActionMaint Port Menu Network Time Upgrade Firmware System UtilityConfig Transfer Ping Configuring WAN Settings ATM ConfigDslam Type Layer One InterfaceATM Stats Data ScramblingAP Receive Cell Errors AP Rx CellsAP Rx OAM Cells AP Receive Cells DiscardedDSL Rate Config Configuring the Router Configuration GlobalUse this menu to enter static routes to other networks Bridge Security Ethernet Ethernet MenuMAC Address WAN This is the network mask used for this interface Use this menu to configure IP settings When set to Y ES, only IP RIP updates are sent All incoming packets from the WAN are not Configuring the Router Status SessionARP cache Bridge TableConfiguring the Router Logs Network Log WrapView ClearConfiguring Voice Support Config Call ControlConfiguring Voice Support Status Gateway StatsPVC Stats Voice StatsManaging the Modules Modules Modules TableManaging the Modules V.35 Setup ConfigurationMode Following settings are used for FRF5 Following settings are used for FRF8 Appendix A. Specifications and Features Network InterfaceATM Support Isdn InterfacesSecurity Features PowerManagement Options Serial DataAppendix B. Updating TA 544 Firmware using Xmodem Updating Firmware via a Forced DownloadPress Enter until a menu appears Updating Firmware via the Console Menus 2001, ADTRAN, Inc Appendix C. Updating TA 544 Firmware using Tftp Message Meaning Message Meaning Enu Path Left Pane Status Bar Ode Avigation H elpWindow Pane Navigation Right Window Pane NotationAdditional Terminal Menu Window Features Navigating Using the Keyboard KeysSession Management Keystrokes Getting Help Application Diagram Voice Turn Up Step Action Appendix F. RFC1483 Quick Start IP Routing WAN Appendix G. RFC1483 Quick Start IP Routing with NAT OptionsAppendix H. RFC1483 Quick Start Bridging Bridging Step ActionAppendix I. PPPoA Quick Start Guide