ADTRAN TA 544 user manual Voice Turn Up Step Action

Page 63

TA 544 User Manual/61200704L1-1A

Page 63 of 68

Voice Turn Up

	Step	Action

	1	From the TA 544 main menu, select the WAN menu. (Here you set up
	1	the ATM network.)
		the ATM network.)

	2	Select the ATM CONFIG menu.

	3	Enter the IDLE CELLS format for your network.

	4	Set DATA SCRAMBLING appropriately for your network.

		Back all the way out to the top level TA 544 menu, and then select the
	5	VOICE menu. (From this menu, the appropriate Voice information for
		working with the Voice Gateway is entered.)

		Select CONFIG, and from the CONFIG menu, enter the Gateway type
		under CALL CONTROL and enter the VPI and VCI values for
	6	communicating with that Gateway.
		CALL CONTROL should be set to the Gateway type and the VPI and VCI
		values should be set appropriately for your network.

		To verify correct setup, use the STATUS menu (under the VOICE menu)
		to look at the current status of the voice connection.
		Under STATUS, you can view the GATEWAY STATS and information
		about the voice PVC along with information about the ISDN ports
	7	available on the Gateway.
		The GATEWAY STATS menu should show the Gateway Link is up (if
		everything is configured correctly).
		A visual inspection of the VOICE LED on the front panel will also yield
		the status. Green = up. Red = Down.

© 2001, ADTRAN, Inc.

TA 544 User Manual

Image 63

Contents 1200704L1 4200704L3 To the Holder of the Manual TrademarksSafety Instructions Limited Product Warranty USA International Contact Information2001, ADTRAN, Inc Repair and Return Customer Service, Product Support Information, and TrainingPresales Inquiries and Applications Support Post-Sale SupportTraining 800 615-1176, ext TrainingContents 2001, ADTRAN, Inc Figures 2001, ADTRAN, Inc Terminal Menu Firmware UpdatesVoice Over DSL Application Mount the Unit Unpack and Inspect the UnitSystem Info Firmware Revision Bootcode RevisionPart Number Serial NumberTelnet Access System ConfigOperating Mode Network Timing ModeSnmp Menu Password Protect Instructions for Changing Passwords Step ActionMaint Port Menu Network Time System Utility Upgrade FirmwareConfig Transfer Ping Layer One Interface Configuring WAN SettingsATM Config Dslam TypeData Scrambling ATM StatsAP Receive Cells Discarded AP Receive Cell ErrorsAP Rx Cells AP Rx OAM CellsDSL Rate Config Global Configuring the Router ConfigurationUse this menu to enter static routes to other networks Bridge Security Ethernet Menu EthernetMAC Address WAN This is the network mask used for this interface Use this menu to configure IP settings When set to Y ES, only IP RIP updates are sent All incoming packets from the WAN are not Bridge Table Configuring the Router StatusSession ARP cacheConfiguring the Router Logs Clear Network LogWrap ViewCall Control Configuring Voice Support ConfigVoice Stats Configuring Voice Support StatusGateway Stats PVC StatsModules Table Managing the Modules ModulesManaging the Modules V.35 Setup ConfigurationMode Following settings are used for FRF5 Following settings are used for FRF8 Isdn Interfaces Appendix A. Specifications and FeaturesNetwork Interface ATM SupportSerial Data Security FeaturesPower Management OptionsAppendix B. Updating TA 544 Firmware using Xmodem Updating Firmware via a Forced DownloadPress Enter until a menu appears Updating Firmware via the Console Menus 2001, ADTRAN, Inc Appendix C. Updating TA 544 Firmware using Tftp Message Meaning Message Meaning Status Bar Ode Avigation H elp Enu Path Left PaneRight Window Pane Notation Window Pane NavigationNavigating Using the Keyboard Keys Additional Terminal Menu Window FeaturesSession Management Keystrokes Getting Help Application Diagram Voice Turn Up Step Action Appendix F. RFC1483 Quick Start IP Routing WAN Options Appendix G. RFC1483 Quick Start IP Routing with NATBridging Step Action Appendix H. RFC1483 Quick Start BridgingAppendix I. PPPoA Quick Start Guide