3Com 09-1324-000 manual Software, Installation Checklists

Page 10

1-2CHAPTER 1: OVERVIEW

Software	The NETBuilder software is available from 3Com on a preinstalled 20 MB ﬂash
	memory card or on CD-ROM. 3Com recommends that you buy the preinstalled
	ﬂash memory card.
	Refer to the NETBuilder II Software Release Notes for information about the
	different software packages that are available for your NETBuilder II system. The
	procedures in this guide apply to all software packages.

Installation Checklists	This section contains a checklist for installing software and booting a NETBuilder II
	with a DPE module and a checklist for installing software and booting a
	NETBuilder II with a CEC 20 module.
	When using the checklists, refer to the chapters that apply to your system:
	■ Chapter 2 and Chapter 3 apply only to NETBuilder II systems that have a DPE
	module.
	■ Chapter 4 and Chapter 5 apply only to NETBuilder II systems that have a CEC
	20 module.
	■ Chapter 6 applies to all NETBuilder II systems.

Image 10

Contents

New Installation for NETBuilder II Software Clara, California 3Com CorporationBayfront Plaza Santa 95052-8145Contents CEC 20 System Index 3COM Corporation Limited Warranty Page About this Guide IntroductionIcon Alerts you to ConventionsList conventions that are used throughout this guide Convention DescriptionOverview Designated as drive aInstallation Checklists SoftwareChange the Primary Boot Source Refer to Chapter Install System Software and Boot Refer to ChapterInstall software from a flash memory card Change the primary boot source default as needed4CHAPTER 1 Overview Booting from the Flash Installing Software and Booting DPE Netbuilder II SystemInstalling Software Performing Initial Boot Memory CardCard Making a BackupFlash Memory NETBuilder II SystemFormat the blank ﬂash memory card in drive B by entering Using the BackupFlash Card Following these stepsPage Command Changing the Boot Source on aUsing the Boot ChangesPrimary boot source Primary Boot SourceConﬁguring Configuring the Primary Boot Source Page Installing Software and Booting CEC 20 Netbuilder II SystemManagement Station Installing SoftwareFrom a Network CD-ROM driveProcedure At the network management stationIf you are using a Bourne sh or Korn ksh shell, enter To see if these daemons are running, enterStation Prerequisites Tftp CD-ROMOver the Network Booting aNETBuilder II Image StationImage/NBII/SW/101/FF/boot.29k To a Flash Memory Copying the SoftwareConﬁguring IP Enter a routing protocol For example, enable RIP using Format the blank ﬂash memory card by enteringPage Slot 7 as the primary boot source You are now ready to enter software commandsFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Logging on to Configuring Basic SettingsSystem User Interface Learning AboutInterface Main menu Level 1 is displayed Reference for NETBuilder Family Software Full-Form SyntaxSymbolDescription SymbolsAbbreviated Syntax Full and Abbreviated Syntax Examples Symbol DescriptionCan be abbreviated to Can be shortened by abbreviating it to Variations in Command SyntaxEntering Service Names in Command Lines Determining the Display of Ports and Virtual PortsCommand History Substitution Using AliasesDisplay it ﬁrst Privilege Level Names Syntax for Assigning ValuesNumeric Values StringsPort and Path Naming Restrictions Media Addresses An example of a Frame Relay address Asynchronous Transfer Mode ATM addressDecimal. The Dlci identiﬁes a virtual circuit on the Frame @22Network Layer Addresses Network from all other IPX networks. The following example For more information on Internet addresses, subnet masks,Followed by the MAC address Addresses are the same 00003333%080002005678Described in Table Getting HelpSyntax Description Manager Privilege Obtaining NetworkLevel Changing PasswordSetting the Time DateAdministrator Setting SystemInformation Assigning Internet Assigning InternetAddresses Addresses to a BridgeInternet addresses to individual ports using SETDefault !2 -IP NETaddr =22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting from a Booting the Netbuilder II CEC a 20 System from the NetworkTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Access by Analog Modem ServicesService Technical Support408 654 2706 or 408 654 Access by Digital ModemPress Return to see the 3ComForum main menu Regional Sales Office Telephone Number 3Com Benelux B.V Regional Sales Office Telephone Number 3Com Corporation3Com Asia Limited 3Com Canada3Com Latin America Regional Sales Office Telephone Number 3Com Iberia3Com Ireland Regional Sales Office Telephone Number 3Com MediterraneoIndex Numericsﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty