3Com 09-1324-000 manual Secondary Boot Source

Page 35

Configuring the Primary Boot Source 5-5

17Enter Q to quit the menu.

Information similar to the following is displayed:

System Configuration
1.	Serial Ports	Console:	9600	Auxiliary:		9600
2.	Self-Test	Skip
3.	Start-Up Action	Try boot forever
4.	Primary Boot Source	Network: Slot: 7		/primary/boot.29k
5.	Secondary Boot Source	Local:	/primary
6.	Test Boot Source	Unknown boot source			Slot:	0
7.	Boot Sources	Primary
8.	Dump Destination	Do not dump

9.Recovery Procedure

10.MP Boot Source

11. Boot StatisticsBooted: 7 Exceptions: 3

Enter parameter number or press Q to quit:

18Ensure that Boot Sources are set to Primary. If the Boot Sources are set correctly, proceed to step 22. If the Boot Sources are not set to Primary and Secondary, proceed to the next step.

19Enter 7 to select Boot Sources.

Information similar to the following is displayed:

Boot Sources: Primary and Secondary

1.Primary

2.Primary and Secondary

3.Secondary

Choose Boot Sources or press Q to quit(CR=Primary and Secondary):

20Enter 2 to select Primary and Secondary.

Information similar to the following is displayed:

Boot Sources: Primary and Secondary

1.Primary

2.Primary and Secondary

3.Secondary

Choose Boot Sources or press Q to quit (CR=Primary):

21Press the Return key to conﬁrm Primary.

Information similar to the following is displayed:

System Configuration
1.	Serial Ports	Console:	9600	Auxiliary:		9600
2.	Self-Test	Skip
3.	Start-Up Action	Try boot forever
4.	Primary Boot Source	Network: Slot: 7		/primary/boot.29k
5. Secondary Boot Source		Local:	/primary
6.	Test Boot Source	Unknown boot source			Slot:	0
7.	Boot Sources	Primary and Secondary
8.	Dump Destination	Do not dump

9.Recovery Procedure

10.MP Boot Source

11. Boot Statistics

Booted: 9

Exceptions: 6

Enter parameter number or press Q to quit:

22Enter Q to quit the ﬁrmware conﬁguration program.

23At the monitor prompt, enter bt to reboot the NETBuilder II bridge/router from ﬁrmware, or enter rb to reboot the bridge/router from software.

Image 35

Contents New Installation for NETBuilder II Software 95052-8145 3Com CorporationBayfront Plaza Santa Clara, CaliforniaContents CEC 20 System Index 3COM Corporation Limited Warranty Page Introduction About this GuideConvention Description ConventionsList conventions that are used throughout this guide Icon Alerts you toDesignated as drive a OverviewSoftware Installation ChecklistsChange the primary boot source default as needed Install System Software and Boot Refer to ChapterInstall software from a flash memory card Change the Primary Boot Source Refer to Chapter4CHAPTER 1 Overview Memory Card Installing Software and Booting DPE Netbuilder II SystemInstalling Software Performing Initial Boot Booting from the FlashNETBuilder II System Making a BackupFlash Memory CardFollowing these steps Using the BackupFlash Card Format the blank ﬂash memory card in drive B by enteringPage Changes Changing the Boot Source on aUsing the Boot CommandConﬁguring Primary Boot SourcePrimary boot source Configuring the Primary Boot Source Page CEC 20 Netbuilder II System Installing Software and BootingCD-ROM drive Installing SoftwareFrom a Network Management StationAt the network management station ProcedureTo see if these daemons are running, enter If you are using a Bourne sh or Korn ksh shell, enterTftp CD-ROM Station PrerequisitesStation Booting aNETBuilder II Image Over the NetworkImage/NBII/SW/101/FF/boot.29k Conﬁguring IP Copying the SoftwareTo a Flash Memory Format the blank ﬂash memory card by entering Enter a routing protocol For example, enable RIP usingPage You are now ready to enter software commands Slot 7 as the primary boot sourceFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page System Configuring Basic SettingsLogging on to Interface Learning AboutUser Interface Main menu Level 1 is displayed Full-Form Syntax Reference for NETBuilder Family SoftwareAbbreviated Syntax SymbolsSymbolDescription Can be abbreviated to Symbol DescriptionFull and Abbreviated Syntax Examples Determining the Display of Ports and Virtual Ports Variations in Command SyntaxEntering Service Names in Command Lines Can be shortened by abbreviating it toDisplay it ﬁrst Using AliasesCommand History Substitution Privilege Level Strings Syntax for Assigning ValuesNumeric Values NamesPort and Path Naming Restrictions Media Addresses @22 Asynchronous Transfer Mode ATM addressDecimal. The Dlci identiﬁes a virtual circuit on the Frame An example of a Frame Relay addressNetwork Layer Addresses Addresses are the same 00003333%080002005678 For more information on Internet addresses, subnet masks,Followed by the MAC address Network from all other IPX networks. The following exampleSyntax Description Getting HelpDescribed in Table Level Obtaining NetworkManager Privilege Date PasswordSetting the Time ChangingInformation Setting SystemAdministrator Addresses to a Bridge Assigning InternetAddresses Assigning InternetSETDefault !2 -IP NETaddr = Internet addresses to individual ports using22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings TFTP/FTP Server Booting the Netbuilder II CEC a 20 System from the NetworkBooting from a NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Technical Support ServicesService Access by Analog ModemPress Return to see the 3ComForum main menu Access by Digital Modem408 654 2706 or 408 654 3Com Canada Regional Sales Office Telephone Number 3Com Corporation3Com Asia Limited Regional Sales Office Telephone Number 3Com Benelux B.VRegional Sales Office Telephone Number 3Com Mediterraneo Regional Sales Office Telephone Number 3Com Iberia3Com Ireland 3Com Latin AmericaNumerics Indexﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty