3Com 09-1324-000 manual firmware 4-6,A-4,A-5

Page 72

2INDEX

menu-driven interface

accessing 6-3limitations 6-3limitations (Note) 6-3

menus, accessing 6-3

N

names assigning 6-10

service, entering 6-7naming restrictions, port/path 6-11NetAccess parameter 6-24NETBuilder II system

disk space requirements A-1EZBuilt Preassembled 1-1

network layer addresses 6-14network management 6-22network management station

PC-based 4-5UNIX-based 4-2

Network Manager privilege level changing password 6-18obtaining 6-17

network service access point. See NSAP network supplier support B-3

NSAP 6-15

numeric values, assigning 6-10

O

online help 6-16

online technical services B-1OSI address format 6-15

P

parameters

firmware 4-6,A-4,A-5

information displayed on selection 6-3values

assigning 6-10storing 6-17

passwords, changing 6-18paths

naming restrictions 6-11using instance identifiers 6-11

ports

naming restrictions 6-11syntax conventions 6-8using instance identifiers 6-11

primary boot source parameters, TFTP A-4privilege level

changing 6-18

changing SNMP access to files 6-23obtaining Network Manager 6-17to access commands and

parameters 6-9

Q

question mark(?) help command 6-16

R

ReBoot command 3-3RemoteManager parameter 6-24repeating displayed commands 6-8

restrictions, naming 6-11returning products for repair B-4root login 4-8,6-1,A-2

S

security 6-24

service names, entering 6-7services, selecting 6-2

set members, specifying 6-9

Simple Network Management Protocol. See

SNMP SNMP

changing manager access to files 6-23displaying/modifying system

parameters 6-22software, installing

from PC-based network management station 4-5

from UNIX-based network management station 4-2

strings case-sensitivity 6-10entering 6-10

using as instance identifiers 6-11syntax, command

abbreviated 6-5,6-6

assigning parameter values 6-10full form 6-4,6-6

ISDN variation 6-11symbols used 6-5variations 6-7

SysconF command 3-2SysPassWord command 6-24system administrator information,

setting 6-19

System Configuration menu 3-3Dump Destination parameter 3-3

T

technical support 3Com URL B-1bulletin board service B-1CompuServe service B-2fax service B-2network suppliers B-3product repair B-4

time and date, setting 6-18

U

URL B-1user interface

command-line 6-2menu-driven 6-2

V

values

assigning numeric 6-10specifying 6-9storing parameter 6-17syntax for assigning 6-10

VIP address format 6-15virtual ports

displaying 6-7functionality (Note) 6-8syntax conventions 6-8

W

World Wide Web (WWW) B-1

X

X.25 address format 6-13XNS address format 6-16

Page 71 Page 73
Image 72
Page 71 Page 73
Contents New Installation for NETBuilder II Software 3Com Corporation Bayfront Plaza SantaClara, California 95052-8145Contents CEC 20 System Index 3COM Corporation Limited Warranty Page About this Guide IntroductionConventions List conventions that are used throughout this guideIcon Alerts you to Convention DescriptionOverview Designated as drive aInstallation Checklists SoftwareInstall System Software and Boot Refer to Chapter Install software from a flash memory cardChange the Primary Boot Source Refer to Chapter Change the primary boot source default as needed4CHAPTER 1 Overview Installing Software and Booting DPE Netbuilder II System Installing Software Performing Initial BootBooting from the Flash Memory CardMaking a Backup Flash MemoryCard NETBuilder II SystemUsing the Backup Flash CardFormat the blank flash memory card in drive B by entering Following these stepsPage Changing the Boot Source on a Using the BootCommand ChangesPrimary Boot Source Primary boot sourceConfiguring Configuring the Primary Boot Source Page Installing Software and Booting CEC 20 Netbuilder II SystemInstalling Software From a NetworkManagement Station CD-ROM driveProcedure At the network management stationIf you are using a Bourne sh or Korn ksh shell, enter To see if these daemons are running, enterStation Prerequisites Tftp CD-ROMBooting a NETBuilder II ImageOver the Network StationImage/NBII/SW/101/FF/boot.29k Copying the Software To a Flash MemoryConfiguring IP Enter a routing protocol For example, enable RIP using Format the blank flash memory card by enteringPage Slot 7 as the primary boot source You are now ready to enter software commandsFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Configuring Basic Settings Logging on toSystem Learning About User InterfaceInterface Main menu Level 1 is displayed Reference for NETBuilder Family Software Full-Form SyntaxSymbols SymbolDescriptionAbbreviated Syntax Symbol Description Full and Abbreviated Syntax ExamplesCan be abbreviated to Variations in Command Syntax Entering Service Names in Command LinesCan be shortened by abbreviating it to Determining the Display of Ports and Virtual PortsUsing Aliases Command History SubstitutionDisplay it first Privilege Level Syntax for Assigning Values Numeric ValuesNames StringsPort and Path Naming Restrictions Media Addresses Asynchronous Transfer Mode ATM address Decimal. The Dlci identifies a virtual circuit on the FrameAn example of a Frame Relay address @22Network Layer Addresses For more information on Internet addresses, subnet masks, Followed by the MAC addressNetwork from all other IPX networks. The following example Addresses are the same 00003333%080002005678Getting Help Described in TableSyntax Description Obtaining Network Manager PrivilegeLevel Password Setting the TimeChanging DateSetting System AdministratorInformation Assigning Internet AddressesAssigning Internet Addresses to a BridgeInternet addresses to individual ports using SETDefault !2 -IP NETaddr =22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting the Netbuilder II CEC a 20 System from the Network Booting from aTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Configuration Token ring port Page Services ServiceAccess by Analog Modem Technical SupportAccess by Digital Modem 408 654 2706 or 408 654Press Return to see the 3ComForum main menu Regional Sales Office Telephone Number 3Com Corporation 3Com Asia LimitedRegional Sales Office Telephone Number 3Com Benelux B.V 3Com CanadaRegional Sales Office Telephone Number 3Com Iberia 3Com Ireland3Com Latin America Regional Sales Office Telephone Number 3Com MediterraneoIndex Numericsfirmware 4-6,A-4,A-5 3Com Corporation Limited Warranty
Top Page Image Contents