3Com 09-1324-000 manual Install System Software and Boot Refer to Chapter

Page 11

Installation Checklists

1-3

NETBuilder II Systems Use the following checklist to install software, boot, and conﬁgure basic settings with a DPE Module on a NETBuilder II system with a DPE module.

Install System Software and Boot — Refer to Chapter 2.

❑Install software from a flash memory card.

Change the Primary Boot Source — Refer to Chapter 3

❑Change the primary boot source default as needed.

Conﬁgure Basic Settings — Refer to Chapter 6.

❑Log on to the system.

❑Familiarize yourself with the command-line or menu-driven user interface (UI), storing conﬁguration parameter values, and getting help.

❑Obtain Network Manager privilege level.

❑Change the Network Manager password.

❑Adjust the time and date if necessary. Time and date are preset and may need to be adjusted for your time zone.

❑Set system administrator information:

❑System name and location

❑System contact name and phone number

❑Assign IP addresses/subnet masks to individual ports or one address to the system.

❑Set up the bridge/router for SNMP.

❑Set up NETBuilder II system security.

❑Use the Quick Installation Utility for further conﬁguration.

Conﬁgure Speciﬁc Services for Your Network — Refer to Using NETBuilder

Family Software and Reference for NETBuilder Family Software.

Image 11

Contents New Installation for NETBuilder II Software 95052-8145 3Com CorporationBayfront Plaza Santa Clara, CaliforniaContents CEC 20 System Index 3COM Corporation Limited Warranty Page Introduction About this GuideConvention Description ConventionsList conventions that are used throughout this guide Icon Alerts you toDesignated as drive a OverviewSoftware Installation ChecklistsChange the primary boot source default as needed Install System Software and Boot Refer to ChapterInstall software from a flash memory card Change the Primary Boot Source Refer to Chapter4CHAPTER 1 Overview Memory Card Installing Software and Booting DPE Netbuilder II SystemInstalling Software Performing Initial Boot Booting from the FlashNETBuilder II System Making a BackupFlash Memory CardFollowing these steps Using the BackupFlash Card Format the blank ﬂash memory card in drive B by enteringPage Changes Changing the Boot Source on aUsing the Boot CommandConﬁguring Primary Boot SourcePrimary boot source Configuring the Primary Boot Source Page CEC 20 Netbuilder II System Installing Software and BootingCD-ROM drive Installing SoftwareFrom a Network Management StationAt the network management station ProcedureTo see if these daemons are running, enter If you are using a Bourne sh or Korn ksh shell, enterTftp CD-ROM Station PrerequisitesStation Booting aNETBuilder II Image Over the NetworkImage/NBII/SW/101/FF/boot.29k Conﬁguring IP Copying the SoftwareTo a Flash Memory Format the blank ﬂash memory card by entering Enter a routing protocol For example, enable RIP usingPage You are now ready to enter software commands Slot 7 as the primary boot sourceFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page System Configuring Basic SettingsLogging on to Interface Learning AboutUser Interface Main menu Level 1 is displayed Full-Form Syntax Reference for NETBuilder Family SoftwareAbbreviated Syntax SymbolsSymbolDescription Can be abbreviated to Symbol DescriptionFull and Abbreviated Syntax Examples Determining the Display of Ports and Virtual Ports Variations in Command SyntaxEntering Service Names in Command Lines Can be shortened by abbreviating it toDisplay it ﬁrst Using AliasesCommand History Substitution Privilege Level Strings Syntax for Assigning ValuesNumeric Values NamesPort and Path Naming Restrictions Media Addresses @22 Asynchronous Transfer Mode ATM addressDecimal. The Dlci identiﬁes a virtual circuit on the Frame An example of a Frame Relay addressNetwork Layer Addresses Addresses are the same 00003333%080002005678 For more information on Internet addresses, subnet masks,Followed by the MAC address Network from all other IPX networks. The following exampleSyntax Description Getting HelpDescribed in Table Level Obtaining NetworkManager Privilege Date PasswordSetting the Time ChangingInformation Setting SystemAdministrator Addresses to a Bridge Assigning InternetAddresses Assigning InternetSETDefault !2 -IP NETaddr = Internet addresses to individual ports using22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings TFTP/FTP Server Booting the Netbuilder II CEC a 20 System from the NetworkBooting from a NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Technical Support ServicesService Access by Analog ModemPress Return to see the 3ComForum main menu Access by Digital Modem408 654 2706 or 408 654 3Com Canada Regional Sales Office Telephone Number 3Com Corporation3Com Asia Limited Regional Sales Office Telephone Number 3Com Benelux B.VRegional Sales Office Telephone Number 3Com Mediterraneo Regional Sales Office Telephone Number 3Com Iberia3Com Ireland 3Com Latin AmericaNumerics Indexﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty