3Com 09-1324-000 manual Index 3COM Corporation Limited Warranty

Page 5

Storing Configuration Parameter Values

6-17

Obtaining Network Manager Privilege Level

6-17

Changing the Password 6-18

 

 

 

Setting the Time and Date

6-18

 

 

 

Setting System Administrator Information

 

6-19

Assigning Internet Addresses

6-20

 

 

Assigning Internet Addresses to a Bridge

6-20

Assigning Internet Addresses to a Router

6-21

Obtaining an Internet Address

6-21

 

 

Setting Up the Simple Network Management Protocol 6-22

Modifying SNMP Parameters

6-23

 

 

NETBuilder Security 6-23

 

 

 

 

Building Firewalls for Security

6-23

 

 

Security Commands and Parameters

6-24

What Next? 6-24

 

 

 

 

ABOOTING THE NETBUILDER II CEC 20 SYSTEM FROM THE NETWORK

Booting from a TFTP/FTP Server A-1

Installing NETBuilder Software on the UNIX-based Network Management Station A-1

Prerequisites A-1

Installing NETBuilder Software

on the UNIX NMS A-2

Setting Up a Unique Configuration File Directory on a TFTP/FTP Server A-3 Setting the Primary Boot Source A-3

More Boot Options A-4 What Next? A-5

B TECHNICAL SUPPORT

Online Technical Services

B-1

 

 

World Wide Web Site

B-1

 

 

3Com Bulletin Board Service

B-1

 

Access by Analog Modem

B-1

 

Access by Digital Modem

B-2

 

3ComFacts Automated Fax Service

B-2

3ComForum on CompuServe Online Service B-2

Support from Your Network Supplier

B-3

Support from 3Com B-3

 

 

 

Returning Products for Repair

B-4

 

INDEX

3COM CORPORATION LIMITED WARRANTY

v

Page 4 Page 6
Image 5
Page 4 Page 6
Contents New Installation for NETBuilder II Software Bayfront Plaza Santa 3Com CorporationClara, California 95052-8145Contents CEC 20 System Index 3COM Corporation Limited Warranty Page Introduction About this GuideList conventions that are used throughout this guide ConventionsIcon Alerts you to Convention DescriptionDesignated as drive a OverviewSoftware Installation ChecklistsInstall software from a flash memory card Install System Software and Boot Refer to ChapterChange the Primary Boot Source Refer to Chapter Change the primary boot source default as needed4CHAPTER 1 Overview Installing Software Performing Initial Boot Installing Software and Booting DPE Netbuilder II SystemBooting from the Flash Memory CardFlash Memory Making a BackupCard NETBuilder II SystemFlash Card Using the BackupFormat the blank flash memory card in drive B by entering Following these stepsPage Using the Boot Changing the Boot Source on aCommand ChangesConfiguring Primary Boot SourcePrimary boot source Configuring the Primary Boot Source Page CEC 20 Netbuilder II System Installing Software and BootingFrom a Network Installing SoftwareManagement Station CD-ROM driveAt the network management station ProcedureTo see if these daemons are running, enter If you are using a Bourne sh or Korn ksh shell, enterTftp CD-ROM Station PrerequisitesNETBuilder II Image Booting aOver the Network StationImage/NBII/SW/101/FF/boot.29k Configuring IP Copying the SoftwareTo a Flash Memory Format the blank flash memory card by entering Enter a routing protocol For example, enable RIP usingPage You are now ready to enter software commands Slot 7 as the primary boot sourceFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page System Configuring Basic SettingsLogging on to Interface Learning AboutUser Interface Main menu Level 1 is displayed Full-Form Syntax Reference for NETBuilder Family SoftwareAbbreviated Syntax SymbolsSymbolDescription Can be abbreviated to Symbol DescriptionFull and Abbreviated Syntax Examples Entering Service Names in Command Lines Variations in Command SyntaxCan be shortened by abbreviating it to Determining the Display of Ports and Virtual PortsDisplay it first Using AliasesCommand History Substitution Privilege Level Numeric Values Syntax for Assigning ValuesNames StringsPort and Path Naming Restrictions Media Addresses Decimal. The Dlci identifies a virtual circuit on the Frame Asynchronous Transfer Mode ATM addressAn example of a Frame Relay address @22Network Layer Addresses Followed by the MAC address For more information on Internet addresses, subnet masks,Network from all other IPX networks. The following example Addresses are the same 00003333%080002005678Syntax Description Getting HelpDescribed in Table Level Obtaining NetworkManager Privilege Setting the Time PasswordChanging DateInformation Setting SystemAdministrator Addresses Assigning InternetAssigning Internet Addresses to a BridgeSETDefault !2 -IP NETaddr = Internet addresses to individual ports using22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings TFTP/FTP Server Booting the Netbuilder II CEC a 20 System from the NetworkBooting from a NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Configuration Token ring port Page Service ServicesAccess by Analog Modem Technical SupportPress Return to see the 3ComForum main menu Access by Digital Modem408 654 2706 or 408 654 3Com Asia Limited Regional Sales Office Telephone Number 3Com CorporationRegional Sales Office Telephone Number 3Com Benelux B.V 3Com Canada3Com Ireland Regional Sales Office Telephone Number 3Com Iberia3Com Latin America Regional Sales Office Telephone Number 3Com MediterraneoNumerics Indexfirmware 4-6,A-4,A-5 3Com Corporation Limited Warranty
Top Page Image Contents