3Com 09-1324-000 Full and Abbreviated Syntax Examples, Can be abbreviated to, Symbol Description

Page 42

6-6CHAPTER 6: CONFIGURING BASIC SETTINGS

Table 6-1Command Syntax Symbols (continued)

Symbol

Description

 

 

vertical bar

Separates mutually exclusive items in a list, one of which must be entered.

 

For example, in the syntax:

 

SET ScreenLength = [None <line>(6–100)]

 

you can specify either the word None or a number between 6 and 100

 

when you enter the command. Do not type the vertical bar.

 

 

ellipsis ...

Following a parameter name or value, indicates that one or more

 

additional arguments may be specified on the same command line. For

 

example, in the syntax:

 

ADD !<port> -IP SecAuthIn <authority> [<authority>

 

...] [ANY]

 

you can specify multiple authorities (GENSER, SIOP, SCI, NSA, DOE, NONE)

 

when you enter the command. Do not type the ellipsis.

 

 

hyphen -

A letter preceded by a hyphen represents a command option. Also, when

 

you enter a service name as part of the command, you must precede the

 

service name with a hyphen. For example, in the command:

 

SETDefault -BRidge CONTrol = Bridge

 

You must include the hyphen with the service name BRidge when you

 

enter the command.

 

 

braces { }

Enclose a list of values, one of which must be entered. For example, in

 

the syntax:

 

SETDefault !<subaddr #> -Gateway SubAddrMap =

 

{(<IPaddr> <PSAPaddr>) None}

 

you must enter either an IP address, PSAP address, or the word None

 

when you enter the command. Do not type the braces.

exclamation point ! A number preceded by an exclamation point represents a port, virtual port, or path number. For example, in the syntax:

SHow [!<port>] -DECnet CONFiguration

the exclamation point must be included before the port number when you enter the command.

The exclamation point is also used to refer to a profile number. Refer to the PROFile Service chapter in Reference for NETBuilder Family Software.

Full and Abbreviated Syntax Examples

The following examples show the full form first, followed by the abbreviated command syntax.

The full-form command syntax:

ADD !<port> -NRIP AdvToNeighbor <network>%<mac address> [...]

can be abbreviated to:

ADD !<port> -NRIP ATN <network>%<mac address> [...]

Replacing the variables in this abbreviated command syntax with values might specify, for example, that a neighbor on port 2, network number &10, with address %080002030ef2, receives RIP and SAP updates:

ADD !2 -NRIP ATN &10%080002030ef2

The full-form command syntax:

SETDefault -IP CONTrol = ([ROute NoROute], [RelaySrcRoute

NoRelaySrcRoute], [SplitLoad NoSplitLoad], [Filtering

NoFiltering], [SECurity NoSECurity], [FwdSubnetBcast

NoFwdSubnetBcast], [FwdAllSubnetBcast NoFwdAllSubnetBcast])

Page 41 Page 43
Image 42
Page 41 Page 43
Contents
New Installation for NETBuilder II Software Clara, California 3Com CorporationBayfront Plaza Santa 95052-8145Contents CEC 20 System Index 3COM Corporation Limited Warranty Page About this Guide IntroductionIcon Alerts you to ConventionsList conventions that are used throughout this guide Convention DescriptionOverview Designated as drive aInstallation Checklists SoftwareChange the Primary Boot Source Refer to Chapter Install System Software and Boot Refer to ChapterInstall software from a flash memory card Change the primary boot source default as needed4CHAPTER 1 Overview Booting from the Flash Installing Software and Booting DPE Netbuilder II SystemInstalling Software Performing Initial Boot Memory CardCard Making a BackupFlash Memory NETBuilder II SystemFormat the blank flash memory card in drive B by entering Using the BackupFlash Card Following these stepsPage Command Changing the Boot Source on aUsing the Boot ChangesPrimary Boot Source Primary boot sourceConfiguring Configuring the Primary Boot Source Page Installing Software and Booting CEC 20 Netbuilder II SystemManagement Station Installing SoftwareFrom a Network CD-ROM driveProcedure At the network management stationIf you are using a Bourne sh or Korn ksh shell, enter To see if these daemons are running, enterStation Prerequisites Tftp CD-ROMOver the Network Booting aNETBuilder II Image StationImage/NBII/SW/101/FF/boot.29k Copying the Software To a Flash MemoryConfiguring IP Enter a routing protocol For example, enable RIP using Format the blank flash memory card by enteringPage Slot 7 as the primary boot source You are now ready to enter software commandsFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Configuring Basic Settings Logging on toSystem Learning About User InterfaceInterface Main menu Level 1 is displayed Reference for NETBuilder Family Software Full-Form SyntaxSymbols SymbolDescriptionAbbreviated Syntax Symbol Description Full and Abbreviated Syntax ExamplesCan be abbreviated to Can be shortened by abbreviating it to Variations in Command SyntaxEntering Service Names in Command Lines Determining the Display of Ports and Virtual PortsUsing Aliases Command History SubstitutionDisplay it first Privilege Level Names Syntax for Assigning ValuesNumeric Values StringsPort and Path Naming Restrictions Media Addresses An example of a Frame Relay address Asynchronous Transfer Mode ATM addressDecimal. The Dlci identifies a virtual circuit on the Frame @22Network Layer Addresses Network from all other IPX networks. The following example For more information on Internet addresses, subnet masks,Followed by the MAC address Addresses are the same 00003333%080002005678Getting Help Described in TableSyntax Description Obtaining Network Manager PrivilegeLevel Changing PasswordSetting the Time DateSetting System AdministratorInformation Assigning Internet Assigning InternetAddresses Addresses to a BridgeInternet addresses to individual ports using SETDefault !2 -IP NETaddr =22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting the Netbuilder II CEC a 20 System from the Network Booting from aTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Configuration Token ring port Page Access by Analog Modem ServicesService Technical SupportAccess by Digital Modem 408 654 2706 or 408 654Press Return to see the 3ComForum main menu Regional Sales Office Telephone Number 3Com Benelux B.V Regional Sales Office Telephone Number 3Com Corporation3Com Asia Limited 3Com Canada3Com Latin America Regional Sales Office Telephone Number 3Com Iberia3Com Ireland Regional Sales Office Telephone Number 3Com MediterraneoIndex Numericsfirmware 4-6,A-4,A-5 3Com Corporation Limited Warranty
Top Page Image Contents