3Com 09-1324-000 manual Conventions, List conventions that are used throughout this guide

Page 8

2ABOUT THIS GUIDE

Appendix A describes how to boot a NETBuilder II system with a CEC 20 from the network using TFTP and Appendix B has instructions on how to obtain technical support.

Conventions

Table 1 and Table 2 list conventions that are used throughout this guide.

 

Table 1

Notice Icons

 

 

 

 

 

 

 

 

 

Icon

Notice Type

Alerts you to...

 

 

 

 

 

 

 

Information note

Important features or instructions

 

 

Caution

 

Risk of personal safety, system damage, or loss of data

 

 

Warning

 

Risk of severe personal injury

 

 

 

 

 

 

Table 2

Text Conventions

 

 

 

 

 

 

Convention

Description

 

 

 

 

 

Syntax

 

Evaluate the syntax provided and supply the appropriate values.

 

 

 

Placeholders for values you must supply appear in angle brackets.

 

 

 

Example:

 

 

 

Enable RIPIP using:

 

 

 

SETDefault !<port> -RIPIP CONTrol = Listen

 

 

 

In this example, you must supply a port number for <port>.

 

 

 

 

Commands

Enter the command exactly as shown in text and press the Return or

 

 

 

Enter key. Example:

 

 

 

To remove the IP address, enter:

 

 

 

SETDefault !0 -IP NETaddr = 0.0.0.0

 

 

 

This guide always gives the full form of a command in uppercase and

 

 

 

 

 

 

lowercase letters. However, you can abbreviate commands by

 

 

 

entering only the uppercase letters and the appropriate value.

 

 

 

 

 

 

Commands are not case-sensitive.

 

 

 

 

Screen displays

This typeface represents information as it appears on the screen.

 

 

 

 

The words “enter”

When you see the word “enter” in this guide, you must type

and “type”

something, and then press the Return or Enter key. Do not press the

 

 

 

Return or Enter key when an instruction simply says “type.”

 

 

 

 

[Key] names

Key names appear in text in one of two ways:

 

 

 

Referred to by their labels, such as “the Return key” or “the

 

 

 

Escape key”

 

 

 

Written with brackets, such as [Return] or [Esc].

 

 

 

If you must press two or more keys simultaneously, the key names

 

 

 

are linked with a plus sign (+). Example:

 

 

 

Press [Ctrl]+[Alt]+[Del].

 

 

 

 

Menu commands

Menu commands or button names appear in italics. Example:

and buttons

From the Help menu, select Contents.

 

 

 

 

 

 

 

Words in italicized

Italics emphasize a point or denote new terms at the place where

type

they are defined in the text.

 

 

 

 

Words in bold-face

Bold text denotes key features.

type

 

 

 

 

 

Image 8 Contents
New Installation for NETBuilder II Software 3Com Corporation Bayfront Plaza SantaClara, California 95052-8145Contents CEC 20 System Index 3COM Corporation Limited Warranty Page About this Guide IntroductionConventions List conventions that are used throughout this guideIcon Alerts you to Convention DescriptionOverview Designated as drive aInstallation Checklists SoftwareInstall System Software and Boot Refer to Chapter Install software from a flash memory cardChange the Primary Boot Source Refer to Chapter Change the primary boot source default as needed4CHAPTER 1 Overview Installing Software and Booting DPE Netbuilder II System Installing Software Performing Initial BootBooting from the Flash Memory CardMaking a Backup Flash MemoryCard NETBuilder II SystemUsing the Backup Flash CardFormat the blank flash memory card in drive B by entering Following these stepsPage Changing the Boot Source on a Using the BootCommand ChangesConfiguring Primary Boot SourcePrimary boot source Configuring the Primary Boot Source Page Installing Software and Booting CEC 20 Netbuilder II SystemInstalling Software From a NetworkManagement Station CD-ROM driveProcedure At the network management stationIf you are using a Bourne sh or Korn ksh shell, enter To see if these daemons are running, enterStation Prerequisites Tftp CD-ROMBooting a NETBuilder II ImageOver the Network StationImage/NBII/SW/101/FF/boot.29k Configuring IP Copying the SoftwareTo a Flash Memory Enter a routing protocol For example, enable RIP using Format the blank flash memory card by enteringPage Slot 7 as the primary boot source You are now ready to enter software commandsFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page System Configuring Basic SettingsLogging on to Interface Learning AboutUser Interface Main menu Level 1 is displayed Reference for NETBuilder Family Software Full-Form SyntaxAbbreviated Syntax SymbolsSymbolDescription Can be abbreviated to Symbol DescriptionFull and Abbreviated Syntax Examples Variations in Command Syntax Entering Service Names in Command LinesCan be shortened by abbreviating it to Determining the Display of Ports and Virtual PortsDisplay it first Using AliasesCommand History Substitution Privilege Level Syntax for Assigning Values Numeric ValuesNames StringsPort and Path Naming Restrictions Media Addresses Asynchronous Transfer Mode ATM address Decimal. The Dlci identifies a virtual circuit on the FrameAn example of a Frame Relay address @22Network Layer Addresses For more information on Internet addresses, subnet masks, Followed by the MAC addressNetwork from all other IPX networks. The following example Addresses are the same 00003333%080002005678Syntax Description Getting HelpDescribed in Table Level Obtaining NetworkManager Privilege Password Setting the TimeChanging DateInformation Setting SystemAdministrator Assigning Internet AddressesAssigning Internet Addresses to a BridgeInternet addresses to individual ports using SETDefault !2 -IP NETaddr =22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings TFTP/FTP Server Booting the Netbuilder II CEC a 20 System from the NetworkBooting from a NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Configuration Token ring port Page Services ServiceAccess by Analog Modem Technical SupportPress Return to see the 3ComForum main menu Access by Digital Modem408 654 2706 or 408 654 Regional Sales Office Telephone Number 3Com Corporation 3Com Asia LimitedRegional Sales Office Telephone Number 3Com Benelux B.V 3Com CanadaRegional Sales Office Telephone Number 3Com Iberia 3Com Ireland3Com Latin America Regional Sales Office Telephone Number 3Com MediterraneoIndex Numericsfirmware 4-6,A-4,A-5 3Com Corporation Limited Warranty