3Com 09-1324-000 manual Image/NBII/SW/101/FF/boot.29k

Page 27

Booting a NETBuilder II Image over the Network 4-7

Procedure

To boot the NETBuilder II image over the network, follow these steps:

1Turn on the NETBuilder II system or press the two outer buttons on the LCD panel on the front of the chassis to reset the system.

2Enter Y when the system asks if you want to enter the monitor.

3From the NETBuilder monitor prompt (>), enter:

SF

The System Configuration menu is displayed.

4Ensure that the System Configuration entry number 3, Start-Up Action, is set to Try boot once.

If Start-Up Action is not set to Try boot once, follow these steps:

aFrom the System Configuration menu, enter 3. The Start-Up Action menu is displayed.

bEnter 3 to select Try boot once and press the Return key.

The System Configuration menu showing the Start-Up Action as Try boot once is displayed.

TFTP is a UDP-based function.Frames may be lost in transit. If this occurs, and the Start-Up Action is not set to Try boot once, lost frames can cause the boot process to continuously retry without success. Set the Start-Up Action to Try boot once to avoid this situation.

5From the System Configuration menu, enter 4 to select Primary Boot Source. The Primary Boot Source menu is displayed.

6Enter 1 to select the Boot Device option, and enter 2 to set the Boot Device to Network.

You are then prompted to set the slot number and boot filename.

7Enter the slot number of the module that is used to reach the TFTP server.

If you have a 4-Slot chassis, your options are 1 through 4. If you have an 8-Slot chassis, your options are 1 through 8.

8Enter the image filename by entering the directory path and the filename relative to the tftpboot directory where the CEC boot image resides.

For example:

/image/NBII/SW/101/FF/boot.29k

You do not need to specify the /tftpboot directory because the TFTP server assumes the /tftpboot directory by default.

9Enter Q to return to the Primary Boot Source menu.

10Enter 5 to select the Boot Protocol option, and set the Primary Boot Protocol to TFTP. You are then prompted to set the TFTP Address Discovery Protocol.

11Set the TFTP Address Discovery Protocol to Local Configured Addresses.

12Enter Q to return to the Primary Boot Source menu.

13Enter 6 to select IP Addresses, and enter the primary IP addresses assigned to the TFTP client, TFTP server, gateway, remote file server, and subnet mask.

Image 27
Contents New Installation for NETBuilder II Software 95052-8145 3Com CorporationBayfront Plaza Santa Clara, CaliforniaContents CEC 20 System Index 3COM Corporation Limited Warranty Page Introduction About this GuideConvention Description ConventionsList conventions that are used throughout this guide Icon Alerts you toDesignated as drive a OverviewSoftware Installation ChecklistsChange the primary boot source default as needed Install System Software and Boot Refer to ChapterInstall software from a flash memory card Change the Primary Boot Source Refer to Chapter4CHAPTER 1 Overview Memory Card Installing Software and Booting DPE Netbuilder II SystemInstalling Software Performing Initial Boot Booting from the FlashNETBuilder II System Making a BackupFlash Memory CardFollowing these steps Using the BackupFlash Card Format the blank flash memory card in drive B by enteringPage Changes Changing the Boot Source on aUsing the Boot CommandPrimary Boot Source Primary boot sourceConfiguring Configuring the Primary Boot Source Page CEC 20 Netbuilder II System Installing Software and BootingCD-ROM drive Installing SoftwareFrom a Network Management StationAt the network management station ProcedureTo see if these daemons are running, enter If you are using a Bourne sh or Korn ksh shell, enterTftp CD-ROM Station PrerequisitesStation Booting aNETBuilder II Image Over the NetworkImage/NBII/SW/101/FF/boot.29k Copying the Software To a Flash MemoryConfiguring IP Format the blank flash memory card by entering Enter a routing protocol For example, enable RIP usingPage You are now ready to enter software commands Slot 7 as the primary boot sourceFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Configuring Basic Settings Logging on toSystem Learning About User InterfaceInterface Main menu Level 1 is displayed Full-Form Syntax Reference for NETBuilder Family SoftwareSymbols SymbolDescriptionAbbreviated Syntax Symbol Description Full and Abbreviated Syntax ExamplesCan be abbreviated to Determining the Display of Ports and Virtual Ports Variations in Command SyntaxEntering Service Names in Command Lines Can be shortened by abbreviating it toUsing Aliases Command History SubstitutionDisplay it first Privilege Level Strings Syntax for Assigning ValuesNumeric Values NamesPort and Path Naming Restrictions Media Addresses @22 Asynchronous Transfer Mode ATM addressDecimal. The Dlci identifies a virtual circuit on the Frame An example of a Frame Relay addressNetwork Layer Addresses Addresses are the same 00003333%080002005678 For more information on Internet addresses, subnet masks,Followed by the MAC address Network from all other IPX networks. The following exampleGetting Help Described in TableSyntax Description Obtaining Network Manager PrivilegeLevel Date PasswordSetting the Time ChangingSetting System AdministratorInformation Addresses to a Bridge Assigning InternetAddresses Assigning InternetSETDefault !2 -IP NETaddr = Internet addresses to individual ports using22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting the Netbuilder II CEC a 20 System from the Network Booting from aTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Configuration Token ring port Page Technical Support ServicesService Access by Analog ModemAccess by Digital Modem 408 654 2706 or 408 654Press Return to see the 3ComForum main menu 3Com Canada Regional Sales Office Telephone Number 3Com Corporation3Com Asia Limited Regional Sales Office Telephone Number 3Com Benelux B.VRegional Sales Office Telephone Number 3Com Mediterraneo Regional Sales Office Telephone Number 3Com Iberia3Com Ireland 3Com Latin AmericaNumerics Indexfirmware 4-6,A-4,A-5 3Com Corporation Limited Warranty