3Com 09-1324-000 manual Reference for NETBuilder Family Software, Full-Form Syntax

Page 40

6-4CHAPTER 6: CONFIGURING BASIC SETTINGS

For more information on ports and paths, refer to Chapter 1 in Using

NETBuilder Family Software. For more information on commands, refer to

Chapter 1 in Reference for NETBuilder Family Software.

bIf the command includes a parameter, type the service name (if necessary), the parameter name, and values.

The service name focuses the action of the command on a particular bridge/router service.

In some cases, you may not need to enter the service name. For example, if a parameter is unique to a service, the service does not need to be specified. If two or more services have parameters of the same name, you must include the service name in the syntax. For more information, refer to “Entering Service Names in Command Lines” on page 6-7.

The value part of the command specifies how you want the parameter to be set. Values include numerics, strings, or addresses, depending on the parameter. For additional information, refer to “Syntax for Assigning Values” on page 6-10.

2After entering the complete command, press the Return key.

The bridge/router software includes online help for commands, services, parameters, and syntax, described in “Getting Help” on page 6-10.The syntax that appears in online help is the full-form syntax; it contains full names and visual cues for entering commands. You can also enter commands using an abbreviated version of the syntax.

For information on full-form and abbreviated syntax, read the following sections and see Figure 6-1and Figure 6-2.For additional information on short cuts for entering commands, refer to “Using Aliases” on page 6-8and “Command History Substitution” on page 6-8.

Full-Form Syntax

To display the full-form syntax (provided by online help in NETBuilder software) type a question mark (?) or a question mark with other options, as described in “Getting Help” on page 6-16.

Figure 6-1shows the parts and symbols that make up command syntax. For more information on symbols, refer to “Symbols” on page 6-5.

Angle brackets enclose variable parameters or values. Do not enter brackets.

Command name

A hyphen always precedes service name and must be entered if the service name is entered.

 

 

 

A vertical bar separates mutually exclusive

 

 

 

 

 

 

values in a list, one of which can be entered.

Service name

Do not enter the bar itself.

 

 

 

 

 

 

 

 

 

 

SETDefault !<path> -FDDI InsertPolicy = [Insert DoNotInsert]

An exclamation point

Parameter name

must precede a port,

 

virtual port, or path number.

 

Square brackets enclose optional values or a list of optional arguments. Do not enter the square brackets.

Figure 6-1Full-Form Syntax

Page 39 Page 41
Image 40
Page 39 Page 41
Contents New Installation for NETBuilder II Software 3Com Corporation Bayfront Plaza SantaClara, California 95052-8145Contents CEC 20 System Index 3COM Corporation Limited Warranty Page About this Guide IntroductionConventions List conventions that are used throughout this guideIcon Alerts you to Convention DescriptionOverview Designated as drive aInstallation Checklists SoftwareInstall System Software and Boot Refer to Chapter Install software from a flash memory cardChange the Primary Boot Source Refer to Chapter Change the primary boot source default as needed4CHAPTER 1 Overview Installing Software and Booting DPE Netbuilder II System Installing Software Performing Initial BootBooting from the Flash Memory CardMaking a Backup Flash MemoryCard NETBuilder II SystemUsing the Backup Flash CardFormat the blank flash memory card in drive B by entering Following these stepsPage Changing the Boot Source on a Using the BootCommand ChangesPrimary boot source Primary Boot SourceConfiguring Configuring the Primary Boot Source Page Installing Software and Booting CEC 20 Netbuilder II SystemInstalling Software From a NetworkManagement Station CD-ROM driveProcedure At the network management stationIf you are using a Bourne sh or Korn ksh shell, enter To see if these daemons are running, enterStation Prerequisites Tftp CD-ROMBooting a NETBuilder II ImageOver the Network StationImage/NBII/SW/101/FF/boot.29k To a Flash Memory Copying the SoftwareConfiguring IP Enter a routing protocol For example, enable RIP using Format the blank flash memory card by enteringPage Slot 7 as the primary boot source You are now ready to enter software commandsFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Logging on to Configuring Basic SettingsSystem User Interface Learning AboutInterface Main menu Level 1 is displayed Reference for NETBuilder Family Software Full-Form SyntaxSymbolDescription SymbolsAbbreviated Syntax Full and Abbreviated Syntax Examples Symbol DescriptionCan be abbreviated to Variations in Command Syntax Entering Service Names in Command LinesCan be shortened by abbreviating it to Determining the Display of Ports and Virtual PortsCommand History Substitution Using AliasesDisplay it first Privilege Level Syntax for Assigning Values Numeric ValuesNames StringsPort and Path Naming Restrictions Media Addresses Asynchronous Transfer Mode ATM address Decimal. The Dlci identifies a virtual circuit on the FrameAn example of a Frame Relay address @22Network Layer Addresses For more information on Internet addresses, subnet masks, Followed by the MAC addressNetwork from all other IPX networks. The following example Addresses are the same 00003333%080002005678Described in Table Getting HelpSyntax Description Manager Privilege Obtaining NetworkLevel Password Setting the TimeChanging DateAdministrator Setting SystemInformation Assigning Internet AddressesAssigning Internet Addresses to a BridgeInternet addresses to individual ports using SETDefault !2 -IP NETaddr =22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting from a Booting the Netbuilder II CEC a 20 System from the NetworkTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Configuration Token ring port Page Services ServiceAccess by Analog Modem Technical Support408 654 2706 or 408 654 Access by Digital ModemPress Return to see the 3ComForum main menu Regional Sales Office Telephone Number 3Com Corporation 3Com Asia LimitedRegional Sales Office Telephone Number 3Com Benelux B.V 3Com CanadaRegional Sales Office Telephone Number 3Com Iberia 3Com Ireland3Com Latin America Regional Sales Office Telephone Number 3Com MediterraneoIndex Numericsfirmware 4-6,A-4,A-5 3Com Corporation Limited Warranty
Top Page Image Contents