3Com 09-1324-000 manual Access by Digital Modem, 408 654 2706 or 408 654

Page 68

B-2APPENDIX B: TECHNICAL SUPPORT

Country

Data Rate

Telephone Number

 

 

 

Mexico

up to 28800 bps

52 5 520 7853

P.R. of China

up to 14400 bps

86 10 684 92351

Singapore

up to 14400 bps

65 534 5693

Taiwan, R.O.C.

up to 14400 bps

886 2 377 5840

U.K.

up to 28800 bps

44 1442 438278

U.S.A.

up to 28800 bps

1 408 980 8204

 

 

 

Access by Digital Modem

ISDN users can dial in to 3ComBBS using a digital modem for fast access up to

56 Kbps. To access 3ComBBS using ISDN, use one of the following numbers:

408 654 2706 or 408 654 2703

3ComFacts Automated 3Com Corporation’s interactive fax service, 3ComFacts, provides data sheets, Fax Service technical articles, diagrams, and troubleshooting instructions on 3Com products

24 hours a day, 7 days a week.

Call 3ComFacts using your Touch-Tone telephone using one of these international access numbers:

Country

Telephone Number

 

 

U.K.

44 1442 438279

U.S.A.

1 408 727 7021

 

 

Local access numbers are available within the following countries:

 

Telephone

Country

Number

 

 

Australia

1800 678 515

Belgium

0800 71279

Denmark

800 17319

Finland

98 001 4444

France

05 90 81 58

Germany

0130 81 80 63

Hong Kong

800 933 486

Italy

1678 99085

Malaysia

1800 801 777

 

 

 

Telephone

Country

Number

 

 

Netherlands

06 0228049

New Zealand

0800 446 398

Norway

800 11062

Portugal

0505 442 607

Russia (Moscow only)

956 0815

Singapore

800 6161 463

Spain

900 964 445

Sweden

020 792954

U.K.

0800 626403

 

 

3ComForum on 3ComForum contains patches, software, drivers, and technical articles about all CompuServe Online 3Com products, as well as a messaging section for peer support. To use

Service 3ComForum, you need a CompuServe account.

To use 3ComForum:

1Log on to your CompuServe account.

2Type go threecom

3Press [Return] to see the 3ComForum main menu.

Image 68
Contents New Installation for NETBuilder II Software 3Com Corporation Bayfront Plaza SantaClara, California 95052-8145Contents CEC 20 System Index 3COM Corporation Limited Warranty Page About this Guide IntroductionConventions List conventions that are used throughout this guideIcon Alerts you to Convention DescriptionOverview Designated as drive aInstallation Checklists SoftwareInstall System Software and Boot Refer to Chapter Install software from a flash memory cardChange the Primary Boot Source Refer to Chapter Change the primary boot source default as needed4CHAPTER 1 Overview Installing Software and Booting DPE Netbuilder II System Installing Software Performing Initial BootBooting from the Flash Memory CardMaking a Backup Flash MemoryCard NETBuilder II SystemUsing the Backup Flash CardFormat the blank flash memory card in drive B by entering Following these stepsPage Changing the Boot Source on a Using the BootCommand ChangesConfiguring Primary Boot SourcePrimary boot source Configuring the Primary Boot Source Page Installing Software and Booting CEC 20 Netbuilder II SystemInstalling Software From a NetworkManagement Station CD-ROM driveProcedure At the network management stationIf you are using a Bourne sh or Korn ksh shell, enter To see if these daemons are running, enterStation Prerequisites Tftp CD-ROMBooting a NETBuilder II ImageOver the Network StationImage/NBII/SW/101/FF/boot.29k Configuring IP Copying the SoftwareTo a Flash Memory Enter a routing protocol For example, enable RIP using Format the blank flash memory card by enteringPage Slot 7 as the primary boot source You are now ready to enter software commandsFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page System Configuring Basic SettingsLogging on to Interface Learning AboutUser Interface Main menu Level 1 is displayed Reference for NETBuilder Family Software Full-Form SyntaxAbbreviated Syntax SymbolsSymbolDescription Can be abbreviated to Symbol DescriptionFull and Abbreviated Syntax Examples Variations in Command Syntax Entering Service Names in Command LinesCan be shortened by abbreviating it to Determining the Display of Ports and Virtual PortsDisplay it first Using AliasesCommand History Substitution Privilege Level Syntax for Assigning Values Numeric ValuesNames StringsPort and Path Naming Restrictions Media Addresses Asynchronous Transfer Mode ATM address Decimal. The Dlci identifies a virtual circuit on the FrameAn example of a Frame Relay address @22Network Layer Addresses For more information on Internet addresses, subnet masks, Followed by the MAC addressNetwork from all other IPX networks. The following example Addresses are the same 00003333%080002005678Syntax Description Getting HelpDescribed in Table Level Obtaining NetworkManager Privilege Password Setting the TimeChanging DateInformation Setting SystemAdministrator Assigning Internet AddressesAssigning Internet Addresses to a BridgeInternet addresses to individual ports using SETDefault !2 -IP NETaddr =22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings TFTP/FTP Server Booting the Netbuilder II CEC a 20 System from the NetworkBooting from a NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Configuration Token ring port Page Services ServiceAccess by Analog Modem Technical SupportPress Return to see the 3ComForum main menu Access by Digital Modem408 654 2706 or 408 654 Regional Sales Office Telephone Number 3Com Corporation 3Com Asia LimitedRegional Sales Office Telephone Number 3Com Benelux B.V 3Com CanadaRegional Sales Office Telephone Number 3Com Iberia 3Com Ireland3Com Latin America Regional Sales Office Telephone Number 3Com MediterraneoIndex Numericsfirmware 4-6,A-4,A-5 3Com Corporation Limited Warranty