3Com 09-1324-000 manual Enter a routing protocol For example, enable RIP using

Page 29

Copying the Software to a Flash Memory Card 4-9

6Enter a routing protocol.

For example, enable RIP using:

SETDefault !<port> -RIPIP CONTrol = (Listen, Talk)

7Conﬁrm your conﬁguration by verifying that the NETBuilder II bridge/router can reach the network management station using:

PING <IP address>

where <IP address> is the IP address of the network management station.

Copying Software to the To copy the software from the network management station to the NETBuilder II NETBuilder II Using TFTP bridge/router using TFTP, follow these steps:

1If you have not already done so, insert a blank ﬂash memory card in drive A.

Refer to the software release notes for a list of ﬂash memory cards that can be used with the CEC 20 module.

For instructions on installing the ﬂash memory drive and inserting a ﬂash memory card, refer to the NETBuilder II Flash Memory Drive Installation Guide.

2Format the blank ﬂash memory card by entering:

FORMAT a:

Type Y at the formatting conﬁrmation message.

3Create a destination directory on the ﬂash memory card.

MakeDir a:/primary

4Copy the NETBuilder II software images from the network management default directory (tftpboot) into the /primary directory on the ﬂash memory card.

For example:

COpy 192.65.74.10:image/NBII/SW/primary/FF/boot.29k a:/primary/boot.29k

where 192.65.74.10 is the IP address of the network management station.

The software images to copy to the NETBuilder II bridge/router may include the following ﬁles:

■boot.29k – Image ﬁle that boots the CEC20 module

■ccsmacro – File that contains predeﬁned user macros

■sys – File that is used during the upgrade process to determine the source and target software versions

■mp6e.29k – Image ﬁle that boots the multiprocessor Ethernet module

■mpatm.29k – Image ﬁle that boots the multiprocessor ATM module

To change your bridge/router primary boot source, refer to Chapter 5.

Image 29

Contents New Installation for NETBuilder II Software Bayfront Plaza Santa 3Com CorporationClara, California 95052-8145Contents CEC 20 System Index 3COM Corporation Limited Warranty Page Introduction About this GuideList conventions that are used throughout this guide ConventionsIcon Alerts you to Convention DescriptionDesignated as drive a OverviewSoftware Installation ChecklistsInstall software from a flash memory card Install System Software and Boot Refer to ChapterChange the Primary Boot Source Refer to Chapter Change the primary boot source default as needed4CHAPTER 1 Overview Installing Software Performing Initial Boot Installing Software and Booting DPE Netbuilder II SystemBooting from the Flash Memory CardFlash Memory Making a BackupCard NETBuilder II SystemFlash Card Using the BackupFormat the blank ﬂash memory card in drive B by entering Following these stepsPage Using the Boot Changing the Boot Source on aCommand ChangesConﬁguring Primary Boot SourcePrimary boot source Configuring the Primary Boot Source Page CEC 20 Netbuilder II System Installing Software and BootingFrom a Network Installing SoftwareManagement Station CD-ROM driveAt the network management station ProcedureTo see if these daemons are running, enter If you are using a Bourne sh or Korn ksh shell, enterTftp CD-ROM Station PrerequisitesNETBuilder II Image Booting aOver the Network StationImage/NBII/SW/101/FF/boot.29k Conﬁguring IP Copying the SoftwareTo a Flash Memory Format the blank ﬂash memory card by entering Enter a routing protocol For example, enable RIP usingPage You are now ready to enter software commands Slot 7 as the primary boot sourceFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page System Configuring Basic SettingsLogging on to Interface Learning AboutUser Interface Main menu Level 1 is displayed Full-Form Syntax Reference for NETBuilder Family SoftwareAbbreviated Syntax SymbolsSymbolDescription Can be abbreviated to Symbol DescriptionFull and Abbreviated Syntax Examples Entering Service Names in Command Lines Variations in Command SyntaxCan be shortened by abbreviating it to Determining the Display of Ports and Virtual PortsDisplay it ﬁrst Using AliasesCommand History Substitution Privilege Level Numeric Values Syntax for Assigning ValuesNames StringsPort and Path Naming Restrictions Media Addresses Decimal. The Dlci identiﬁes a virtual circuit on the Frame Asynchronous Transfer Mode ATM addressAn example of a Frame Relay address @22Network Layer Addresses Followed by the MAC address For more information on Internet addresses, subnet masks,Network from all other IPX networks. The following example Addresses are the same 00003333%080002005678Syntax Description Getting HelpDescribed in Table Level Obtaining NetworkManager Privilege Setting the Time PasswordChanging DateInformation Setting SystemAdministrator Addresses Assigning InternetAssigning Internet Addresses to a BridgeSETDefault !2 -IP NETaddr = Internet addresses to individual ports using22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings TFTP/FTP Server Booting the Netbuilder II CEC a 20 System from the NetworkBooting from a NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Service ServicesAccess by Analog Modem Technical SupportPress Return to see the 3ComForum main menu Access by Digital Modem408 654 2706 or 408 654 3Com Asia Limited Regional Sales Office Telephone Number 3Com CorporationRegional Sales Office Telephone Number 3Com Benelux B.V 3Com Canada3Com Ireland Regional Sales Office Telephone Number 3Com Iberia3Com Latin America Regional Sales Office Telephone Number 3Com MediterraneoNumerics Indexﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty