3Com 09-1324-000 manual Enter 4 to select Primary Boot Source

Page 33

Configuring the Primary Boot Source 5-3

8. Dump Destination

Do not dump

9.Recovery Procedure

10.MP Boot Source

11. Boot Statistics	Booted: 7	Exceptions: 3
Enter parameter number or press Q to quit:

Enter 4 to select Primary Boot Source.

Information similar to the following is displayed:

Primary Boot Source:
1.	Boot Device:	Drive A:
2.	Default file source	Local:
3.	Maximum retries	0
4.	I/O Module Parameters Ethernet
5.	Boot Protocol	TFTP Local configured addresses
6.	IP Addresses	client:none
		Subnet Mask:none
7.	MAC Address System	08-00-02-05-1A-BE
8.	ARP Format	Canonical
9.	FTP Login Parameters

Enter parameter number or press Q to quit:

8Enter 1 to select Boot Device.

Information similar to the following is displayed:

Primary Boot Device:

Local: Drive A:

1.Local

2.Network

Choose Primary Boot Device or press Q to quit:

9Enter 2 to select Network.

Information similar to the following is displayed:

Network Boot:

Choose a slot :

10Enter the slot number where the CEC 20 is installed. For example, type 7 to specify slot 7.

Information similar to the following is displayed:

Boot Filename: boot.29k

Enter Boot Filename (CR=no change):

11Select the NETBuilder bridge/router software version 10.1 as the default boot source ﬁle by entering:

/primary/boot.29k

Information similar to the following is displayed:

Primary Boot Device:

Network: Slot 7: /primary/boot.29k

1.Local

2.Network

Choose Primary Boot Device or press Q to quit:

Image 33

Contents New Installation for NETBuilder II Software Bayfront Plaza Santa 3Com CorporationClara, California 95052-8145Contents CEC 20 System Index 3COM Corporation Limited Warranty Page Introduction About this GuideList conventions that are used throughout this guide ConventionsIcon Alerts you to Convention DescriptionDesignated as drive a OverviewSoftware Installation ChecklistsInstall software from a flash memory card Install System Software and Boot Refer to ChapterChange the Primary Boot Source Refer to Chapter Change the primary boot source default as needed4CHAPTER 1 Overview Installing Software Performing Initial Boot Installing Software and Booting DPE Netbuilder II SystemBooting from the Flash Memory CardFlash Memory Making a BackupCard NETBuilder II SystemFlash Card Using the BackupFormat the blank ﬂash memory card in drive B by entering Following these stepsPage Using the Boot Changing the Boot Source on aCommand ChangesPrimary Boot Source Primary boot sourceConﬁguring Configuring the Primary Boot Source Page CEC 20 Netbuilder II System Installing Software and BootingFrom a Network Installing SoftwareManagement Station CD-ROM driveAt the network management station ProcedureTo see if these daemons are running, enter If you are using a Bourne sh or Korn ksh shell, enterTftp CD-ROM Station PrerequisitesNETBuilder II Image Booting aOver the Network StationImage/NBII/SW/101/FF/boot.29k Copying the Software To a Flash MemoryConﬁguring IP Format the blank ﬂash memory card by entering Enter a routing protocol For example, enable RIP usingPage You are now ready to enter software commands Slot 7 as the primary boot sourceFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Configuring Basic Settings Logging on toSystem Learning About User InterfaceInterface Main menu Level 1 is displayed Full-Form Syntax Reference for NETBuilder Family SoftwareSymbols SymbolDescriptionAbbreviated Syntax Symbol Description Full and Abbreviated Syntax ExamplesCan be abbreviated to Entering Service Names in Command Lines Variations in Command SyntaxCan be shortened by abbreviating it to Determining the Display of Ports and Virtual PortsUsing Aliases Command History SubstitutionDisplay it ﬁrst Privilege Level Numeric Values Syntax for Assigning ValuesNames StringsPort and Path Naming Restrictions Media Addresses Decimal. The Dlci identiﬁes a virtual circuit on the Frame Asynchronous Transfer Mode ATM addressAn example of a Frame Relay address @22Network Layer Addresses Followed by the MAC address For more information on Internet addresses, subnet masks,Network from all other IPX networks. The following example Addresses are the same 00003333%080002005678Getting Help Described in TableSyntax Description Obtaining Network Manager PrivilegeLevel Setting the Time PasswordChanging DateSetting System AdministratorInformation Addresses Assigning InternetAssigning Internet Addresses to a BridgeSETDefault !2 -IP NETaddr = Internet addresses to individual ports using22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting the Netbuilder II CEC a 20 System from the Network Booting from aTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Service ServicesAccess by Analog Modem Technical SupportAccess by Digital Modem 408 654 2706 or 408 654Press Return to see the 3ComForum main menu 3Com Asia Limited Regional Sales Office Telephone Number 3Com CorporationRegional Sales Office Telephone Number 3Com Benelux B.V 3Com Canada3Com Ireland Regional Sales Office Telephone Number 3Com Iberia3Com Latin America Regional Sales Office Telephone Number 3Com MediterraneoNumerics Indexﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty