3Com 09-1324-000 manual Copying the Software, To a Flash Memory, Conﬁguring IP

Page 28

4-8CHAPTER 4: INSTALLING SOFTWARE AND BOOTING A CEC 20 NETBUILDER II SYSTEM

14Enter Q repeatedly to return to the System Conﬁguration menu.

15Ensure that Boot Sources is set to Primary and Secondary. If Boot Sources is not set correctly, follow these steps:

a From the System Conﬁguration menu, enter 7. b From the Boot Sources menu, enter 2.

16Exit the menu system by typing Q repeatedly.

17To boot the software image from the network management station, enter:

NB

	The bridge/router obtains its software image from the network management
	station and boots.
	When the following message is displayed:
	System Initialized and Running
	the bridge/router has ﬁnished booting.

Copying the Software	To boot locally, the software image boot ﬁle must be copied to the ﬂash memory
to a Flash Memory	card in drive A.
Card
Conﬁguring IP	Before you copy the software to the NETBuilder II bridge/router ﬂash memory
	card, you must conﬁgure IP for the port that the NETBuilder II bridge/router can be
	accessed through.
	This procedure assumes that you have just booted the NETBuilder bridge/router
	over the network.
	To conﬁgure IP on the NETBuilder II bridge/router, follow these steps:

1Press the Return key.

The following prompt is displayed on the console:

NetLogin:

2Log on as root:

root

3Press the Return key.

Pressing the Return key when prompted for the password enters a null string, which is the default local password.

The bridge/router system prompt is displayed:

NETBuilder #

You are now ready to begin using the software and entering software commands.

4Set up an IP address and subnet mask using:

SETDefault !<port> -IP NETaddr = <IP address> [<subnet mask>]

For more information on IP conﬁguration, refer to Reference for NETBuilder Family

Software.

5Enable IP routing by entering:

SETDefault -IP CONTrol = RO

Image 28

Contents New Installation for NETBuilder II Software 3Com Corporation Bayfront Plaza SantaClara, California 95052-8145Contents CEC 20 System Index 3COM Corporation Limited Warranty Page About this Guide IntroductionConventions List conventions that are used throughout this guideIcon Alerts you to Convention DescriptionOverview Designated as drive aInstallation Checklists SoftwareInstall System Software and Boot Refer to Chapter Install software from a flash memory cardChange the Primary Boot Source Refer to Chapter Change the primary boot source default as needed4CHAPTER 1 Overview Installing Software and Booting DPE Netbuilder II System Installing Software Performing Initial BootBooting from the Flash Memory CardMaking a Backup Flash MemoryCard NETBuilder II SystemUsing the Backup Flash CardFormat the blank ﬂash memory card in drive B by entering Following these stepsPage Changing the Boot Source on a Using the BootCommand ChangesPrimary boot source Primary Boot SourceConﬁguring Configuring the Primary Boot Source Page Installing Software and Booting CEC 20 Netbuilder II SystemInstalling Software From a NetworkManagement Station CD-ROM driveProcedure At the network management stationIf you are using a Bourne sh or Korn ksh shell, enter To see if these daemons are running, enterStation Prerequisites Tftp CD-ROMBooting a NETBuilder II ImageOver the Network StationImage/NBII/SW/101/FF/boot.29k To a Flash Memory Copying the SoftwareConﬁguring IP Enter a routing protocol For example, enable RIP using Format the blank ﬂash memory card by enteringPage Slot 7 as the primary boot source You are now ready to enter software commandsFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Logging on to Configuring Basic SettingsSystem User Interface Learning AboutInterface Main menu Level 1 is displayed Reference for NETBuilder Family Software Full-Form SyntaxSymbolDescription SymbolsAbbreviated Syntax Full and Abbreviated Syntax Examples Symbol DescriptionCan be abbreviated to Variations in Command Syntax Entering Service Names in Command LinesCan be shortened by abbreviating it to Determining the Display of Ports and Virtual PortsCommand History Substitution Using AliasesDisplay it ﬁrst Privilege Level Syntax for Assigning Values Numeric ValuesNames StringsPort and Path Naming Restrictions Media Addresses Asynchronous Transfer Mode ATM address Decimal. The Dlci identiﬁes a virtual circuit on the FrameAn example of a Frame Relay address @22Network Layer Addresses For more information on Internet addresses, subnet masks, Followed by the MAC addressNetwork from all other IPX networks. The following example Addresses are the same 00003333%080002005678Described in Table Getting HelpSyntax Description Manager Privilege Obtaining NetworkLevel Password Setting the TimeChanging DateAdministrator Setting SystemInformation Assigning Internet AddressesAssigning Internet Addresses to a BridgeInternet addresses to individual ports using SETDefault !2 -IP NETaddr =22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting from a Booting the Netbuilder II CEC a 20 System from the NetworkTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Services ServiceAccess by Analog Modem Technical Support408 654 2706 or 408 654 Access by Digital ModemPress Return to see the 3ComForum main menu Regional Sales Office Telephone Number 3Com Corporation 3Com Asia LimitedRegional Sales Office Telephone Number 3Com Benelux B.V 3Com CanadaRegional Sales Office Telephone Number 3Com Iberia 3Com Ireland3Com Latin America Regional Sales Office Telephone Number 3Com MediterraneoIndex Numericsﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty