3Com 09-1324-000 manual Changing, Password, Setting the Time, Date

Page 54

6-18CHAPTER 6: CONFIGURING BASIC SETTINGS

The following prompt is displayed at the User privilege level:

NETBuilder >

2If you are currently at User privilege level, enter the following command to change the privilege level from User to Network Manager:

SET PRIvilege = NetMgr

The following prompt is displayed:

Password:

3Press the Return key.

A null string is entered, which is the default password.

After obtaining Network Manager privilege, proceed to the next section to change the Network Manager password.

Changing the	Changing the Network Manager password prevents unauthorized users from
Password	accessing the bridge/router. You should change the password immediately after you
	log on for the ﬁrst time.

	The privilege level determines which commands and parameters a user can access.
	Each level has its own password. You must set the Network Manager password and
	the User password to be the same in order to provide equal levels of security. If only
	the Network Manager password is set, any other user receives User level privileges.
	Users with NetMgr privileges can lower their privileges without a password. Users
	with User privileges cannot raise their privileges. To raise privileges after lowering
	them, you must enter the password again.
	The Network Manager password must be set before the User password. The User
	password must be cleared before the Network Manager password.
	To change the password, follow these steps:
1	At the NETBuilder prompt (NETBuilder #), enter:
	SysPassWord
	When a menu is displayed, Select 1, Set Network Manager Privilege Password.
2	Enter the new Network Manager password. Retype it when prompted to do so.
	You are returned to the SysPassWord menu.
3	Enter 2.
4	Enter the new User password and retype it when prompted to do so.
5	Press the Return key to exit the SysPassWord menu and return to the NETBuilder
	prompt (NETBuilder #).
	Go to the next section to set the time and date on the system.

Setting the Time and	To set the time and date on your system, use:
Date	SET -SYS DATE = YY/MM/DD HH:MM[:ss]
	SET -SYS DATE = YY/MM/DD HH:MM[:ss]

For example, to set the date and time to January 10, 1995, 9:40 a.m., enter:

SET -SYS DATE = 1995/1/10 09:40

Image 54

Contents New Installation for NETBuilder II Software Clara, California 3Com CorporationBayfront Plaza Santa 95052-8145Contents CEC 20 System Index 3COM Corporation Limited Warranty Page About this Guide IntroductionIcon Alerts you to ConventionsList conventions that are used throughout this guide Convention DescriptionOverview Designated as drive aInstallation Checklists SoftwareChange the Primary Boot Source Refer to Chapter Install System Software and Boot Refer to ChapterInstall software from a flash memory card Change the primary boot source default as needed4CHAPTER 1 Overview Booting from the Flash Installing Software and Booting DPE Netbuilder II SystemInstalling Software Performing Initial Boot Memory CardCard Making a BackupFlash Memory NETBuilder II SystemFormat the blank ﬂash memory card in drive B by entering Using the BackupFlash Card Following these stepsPage Command Changing the Boot Source on aUsing the Boot ChangesPrimary Boot Source Primary boot sourceConﬁguring Configuring the Primary Boot Source Page Installing Software and Booting CEC 20 Netbuilder II SystemManagement Station Installing SoftwareFrom a Network CD-ROM driveProcedure At the network management stationIf you are using a Bourne sh or Korn ksh shell, enter To see if these daemons are running, enterStation Prerequisites Tftp CD-ROMOver the Network Booting aNETBuilder II Image StationImage/NBII/SW/101/FF/boot.29k Copying the Software To a Flash MemoryConﬁguring IP Enter a routing protocol For example, enable RIP using Format the blank ﬂash memory card by enteringPage Slot 7 as the primary boot source You are now ready to enter software commandsFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Configuring Basic Settings Logging on toSystem Learning About User InterfaceInterface Main menu Level 1 is displayed Reference for NETBuilder Family Software Full-Form SyntaxSymbols SymbolDescriptionAbbreviated Syntax Symbol Description Full and Abbreviated Syntax ExamplesCan be abbreviated to Can be shortened by abbreviating it to Variations in Command SyntaxEntering Service Names in Command Lines Determining the Display of Ports and Virtual PortsUsing Aliases Command History SubstitutionDisplay it ﬁrst Privilege Level Names Syntax for Assigning ValuesNumeric Values StringsPort and Path Naming Restrictions Media Addresses An example of a Frame Relay address Asynchronous Transfer Mode ATM addressDecimal. The Dlci identiﬁes a virtual circuit on the Frame @22Network Layer Addresses Network from all other IPX networks. The following example For more information on Internet addresses, subnet masks,Followed by the MAC address Addresses are the same 00003333%080002005678Getting Help Described in TableSyntax Description Obtaining Network Manager PrivilegeLevel Changing PasswordSetting the Time DateSetting System AdministratorInformation Assigning Internet Assigning InternetAddresses Addresses to a BridgeInternet addresses to individual ports using SETDefault !2 -IP NETaddr =22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting the Netbuilder II CEC a 20 System from the Network Booting from aTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Access by Analog Modem ServicesService Technical SupportAccess by Digital Modem 408 654 2706 or 408 654Press Return to see the 3ComForum main menu Regional Sales Office Telephone Number 3Com Benelux B.V Regional Sales Office Telephone Number 3Com Corporation3Com Asia Limited 3Com Canada3Com Latin America Regional Sales Office Telephone Number 3Com Iberia3Com Ireland Regional Sales Office Telephone Number 3Com MediterraneoIndex Numericsﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty