3Com 09-1324-000 manual Procedure, At the network management station

Page 23

Installing Software from a Network Management Station 4-3

Before installing the software from CD-ROM, make sure that:

■Your network management station is running Solaris 2.4 or 2.5x, SunOS 4.1.4, HP-UX 9.0.5, 10.10 or 10.20, or IBM AIX 3.2.5, 4.1.4 or 4.2. To verify the operating system environment, enter:

uname -a

The version message refers to Solaris 2.5x as SunOS 5.5.

■You know the root password.

■The network management station has sufﬁcient disk space for the amount of software you are installing. Minimal disk storage requirements are dependent on the number of NETBuilder systems being installed. Allocate 40 MB for the NETBuilder Upgrade Management Utilities and software image, 4 MB for each NETBuilder II system.

■The NETBuilder Upgrade Management Utilities released with this software package have been installed on the network management station. Refer to Upgrading NETBuilder Family Software for more information.

■Install a blank ﬂash memory card in the NETBuilder II bridge/router. For installation instructions, refer to the NETBuilder II Flash Memory Drive Installation Guide.

For a list of ﬂash memory cards that can be used with the CEC 20 module, refer to the software release notes.

At the network management station:

aInsert NETBuilder II software CD-ROM into CD-ROM drive on NMS

bCopy the NETBuilder II software to TFTP boot directory on NMS

cSelect TFTP file in the NMS as primary boot source

At the console:

d Set up IP routing

e Transfer software to NETBuilder II with TFTP

Console

UNIX-based NMS

Running recommended

CD-ROM

CEC 20 module

TFTP

TCP network

CEC					CONSOLE	AUXILIARY	DIAGNOSTIC
			CPU ACT	PKT FWD	CONSOLE	AUXILIARY	DIAGNOSTIC
SELF TEST
1	2	3	4 BOOT	POWER	STATUS
1	2	3	4 BOOT	POWER
			BYPASS				8
		A STATUS		B STATUS
1					STATUS
1
			A	B			7
							7
2
							6
3
							5
4

NETBuilder II bridge/router

Figure 4-1Installing NETBuilder II Software from CD-ROM on a UNIX NMS

Procedure

To install the NETBuilder software on the UNIX network management station, follow these steps:

1Format the blank ﬂash memory card in drive A by entering:

FORMAT A:

Type Y for yes when the formatting conﬁrmation message is displayed.

Image 23

Contents New Installation for NETBuilder II Software 95052-8145 3Com CorporationBayfront Plaza Santa Clara, CaliforniaContents CEC 20 System Index 3COM Corporation Limited Warranty Page Introduction About this GuideConvention Description ConventionsList conventions that are used throughout this guide Icon Alerts you toDesignated as drive a OverviewSoftware Installation ChecklistsChange the primary boot source default as needed Install System Software and Boot Refer to ChapterInstall software from a flash memory card Change the Primary Boot Source Refer to Chapter4CHAPTER 1 Overview Memory Card Installing Software and Booting DPE Netbuilder II SystemInstalling Software Performing Initial Boot Booting from the FlashNETBuilder II System Making a BackupFlash Memory CardFollowing these steps Using the BackupFlash Card Format the blank ﬂash memory card in drive B by enteringPage Changes Changing the Boot Source on aUsing the Boot CommandConﬁguring Primary Boot SourcePrimary boot source Configuring the Primary Boot Source Page CEC 20 Netbuilder II System Installing Software and BootingCD-ROM drive Installing SoftwareFrom a Network Management StationAt the network management station ProcedureTo see if these daemons are running, enter If you are using a Bourne sh or Korn ksh shell, enterTftp CD-ROM Station PrerequisitesStation Booting aNETBuilder II Image Over the NetworkImage/NBII/SW/101/FF/boot.29k Conﬁguring IP Copying the SoftwareTo a Flash Memory Format the blank ﬂash memory card by entering Enter a routing protocol For example, enable RIP usingPage You are now ready to enter software commands Slot 7 as the primary boot sourceFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page System Configuring Basic SettingsLogging on to Interface Learning AboutUser Interface Main menu Level 1 is displayed Full-Form Syntax Reference for NETBuilder Family SoftwareAbbreviated Syntax SymbolsSymbolDescription Can be abbreviated to Symbol DescriptionFull and Abbreviated Syntax Examples Determining the Display of Ports and Virtual Ports Variations in Command SyntaxEntering Service Names in Command Lines Can be shortened by abbreviating it toDisplay it ﬁrst Using AliasesCommand History Substitution Privilege Level Strings Syntax for Assigning ValuesNumeric Values NamesPort and Path Naming Restrictions Media Addresses @22 Asynchronous Transfer Mode ATM addressDecimal. The Dlci identiﬁes a virtual circuit on the Frame An example of a Frame Relay addressNetwork Layer Addresses Addresses are the same 00003333%080002005678 For more information on Internet addresses, subnet masks,Followed by the MAC address Network from all other IPX networks. The following exampleSyntax Description Getting HelpDescribed in Table Level Obtaining NetworkManager Privilege Date PasswordSetting the Time ChangingInformation Setting SystemAdministrator Addresses to a Bridge Assigning InternetAddresses Assigning InternetSETDefault !2 -IP NETaddr = Internet addresses to individual ports using22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings TFTP/FTP Server Booting the Netbuilder II CEC a 20 System from the NetworkBooting from a NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Technical Support ServicesService Access by Analog ModemPress Return to see the 3ComForum main menu Access by Digital Modem408 654 2706 or 408 654 3Com Canada Regional Sales Office Telephone Number 3Com Corporation3Com Asia Limited Regional Sales Office Telephone Number 3Com Benelux B.VRegional Sales Office Telephone Number 3Com Mediterraneo Regional Sales Office Telephone Number 3Com Iberia3Com Ireland 3Com Latin AmericaNumerics Indexﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty