3Com 09-1324-000 manual Getting Help, Described in Table, Syntax Description

Page 52

6-16CHAPTER 6: CONFIGURING BASIC SETTINGS

	XNS	Consists of a network address followed by a MAC address. The
		network address distinguishes between different XNS Ethernet
		networks. It contains eight hexadecimal digits, and is preceded by an
		ampersand (&), which is used for identiﬁcation. Leading zeros can be
		omitted. The following addresses are the same:
		&3333%080002001326
		&00003333%080002001326

Getting Help	The user interface provides help menus as memory aids. To display the help menu,
	enter a question mark (?). The question mark can be used with different options as
	described in Table 6-5.
	Table 6-5Online Help Syntax Summary

	Syntax		Description

	?		Displays the help menu. Different commands are displayed de-
			pending on whether Network Manager privilege or User privilege is in
			effect. The commands are organized according to services.

	-?		Displays a list of services.

	-service?		Displays a list of commands within the service.
			For example, to display a list of commands in the SYS Service, enter:
			-SYS?
			If there are no commands under the service, a message is displayed to
			indicate this. For example, enter this command at the prompt:
			-IDP?
			A message similar to the following appears:
			No commands available in IDP service

	command -service?		Displays a list of parameters that can be used with the command
			within the service.
			For example, to display a list of PORT Service parameters that can be
			used with the SETDefault command, enter:
			SETDefault -PORT?

	command ?		Displays parameters by service name that can be used with the
			command. Only parameters in services specified by the CurrentServices
			parameter are displayed.

command -service parameter?

Displays syntax for the command used with the parameter.

For example, to display the syntax for the SETDefault command used with the CONTrol parameter in the SNMP Service, enter:

SETDefault -SNMP CONTrol?

Setting up IP Routing You must set up the port that accesses the server for IP routing. To set up IP routing, follow these steps:

1Log on as root and press the Return key. The password prompt is displayed.

2At the password prompt, press the Return key.

The network manager prompt (NETBuilder #) is displayed.

3Set up an IP address and subnet mask using:

SETDefault !<port> -IP NETaddr = <IP address> [<subnet mask>]

Image 52

Contents

New Installation for NETBuilder II Software 3Com Corporation Bayfront Plaza SantaClara, California 95052-8145Contents CEC 20 System Index 3COM Corporation Limited Warranty Page About this Guide IntroductionConventions List conventions that are used throughout this guideIcon Alerts you to Convention DescriptionOverview Designated as drive aInstallation Checklists SoftwareInstall System Software and Boot Refer to Chapter Install software from a flash memory cardChange the Primary Boot Source Refer to Chapter Change the primary boot source default as needed4CHAPTER 1 Overview Installing Software and Booting DPE Netbuilder II System Installing Software Performing Initial BootBooting from the Flash Memory CardMaking a Backup Flash MemoryCard NETBuilder II SystemUsing the Backup Flash CardFormat the blank ﬂash memory card in drive B by entering Following these stepsPage Changing the Boot Source on a Using the BootCommand ChangesPrimary boot source Primary Boot SourceConﬁguring Configuring the Primary Boot Source Page Installing Software and Booting CEC 20 Netbuilder II SystemInstalling Software From a NetworkManagement Station CD-ROM driveProcedure At the network management stationIf you are using a Bourne sh or Korn ksh shell, enter To see if these daemons are running, enterStation Prerequisites Tftp CD-ROMBooting a NETBuilder II ImageOver the Network StationImage/NBII/SW/101/FF/boot.29k To a Flash Memory Copying the SoftwareConﬁguring IP Enter a routing protocol For example, enable RIP using Format the blank ﬂash memory card by enteringPage Slot 7 as the primary boot source You are now ready to enter software commandsFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Logging on to Configuring Basic SettingsSystem User Interface Learning AboutInterface Main menu Level 1 is displayed Reference for NETBuilder Family Software Full-Form SyntaxSymbolDescription SymbolsAbbreviated Syntax Full and Abbreviated Syntax Examples Symbol DescriptionCan be abbreviated to Variations in Command Syntax Entering Service Names in Command LinesCan be shortened by abbreviating it to Determining the Display of Ports and Virtual PortsCommand History Substitution Using AliasesDisplay it ﬁrst Privilege Level Syntax for Assigning Values Numeric ValuesNames StringsPort and Path Naming Restrictions Media Addresses Asynchronous Transfer Mode ATM address Decimal. The Dlci identiﬁes a virtual circuit on the Frame An example of a Frame Relay address @22Network Layer Addresses For more information on Internet addresses, subnet masks, Followed by the MAC addressNetwork from all other IPX networks. The following example Addresses are the same 00003333%080002005678Described in Table Getting HelpSyntax Description Manager Privilege Obtaining NetworkLevel Password Setting the TimeChanging DateAdministrator Setting SystemInformation Assigning Internet AddressesAssigning Internet Addresses to a BridgeInternet addresses to individual ports using SETDefault !2 -IP NETaddr =22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting from a Booting the Netbuilder II CEC a 20 System from the NetworkTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Services ServiceAccess by Analog Modem Technical Support408 654 2706 or 408 654 Access by Digital ModemPress Return to see the 3ComForum main menu Regional Sales Office Telephone Number 3Com Corporation 3Com Asia LimitedRegional Sales Office Telephone Number 3Com Benelux B.V 3Com CanadaRegional Sales Office Telephone Number 3Com Iberia 3Com Ireland3Com Latin America Regional Sales Office Telephone Number 3Com MediterraneoIndex Numericsﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty