3Com 09-1324-000 manual Configuring the Primary Boot Source

Page 19

Configuring the Primary Boot Source 3-3

5Enter 1 to select a boot ﬁlename.

Information similar to the following is displayed:

Current Boot Filename: a:/101/boot.29k

Enter Boot Filename (CR = no change):

6Enter a new boot ﬁlename (such as b:/101/boot.29k) and press the Return key.

The conﬁguration ﬁles must reside on the same drive as the boot source. If the drive you specify is different from the conﬁguration boot source drive, you are prompted to change the conﬁguration ﬁle source to the same drive.

If the boot drive you specify conﬂicts with the one set in the Dump Destination parameter, you are prompted for a different drive.

7Enter q to quit the menu.

The System Conﬁguration menu showing the new entries is displayed:

System Configuration
1.	Serial Ports	Console: 9600
2.	Primary Boot Source	b:/101/boot.29k, b:/
3.	Secondary Boot Source	b:/boot.29k,	b:/
4.	Test Boot Source	a:/boot.29k,	a:/:
5.	Boot Sources	Primary and Secondary
6.	Dump Destination	Partial dump	only

7.Recovery Procedure

8.MP Boot Source

9. Boot StatisticsBooted: 1 Exceptions: 0 Enter parameter number or press Q to quit:

8Enter q to quit the conﬁguration program.

9At the prompt, enter:

ReBoot

The NETBuilder II bridge/router reboots using the newly established drive B as the primary boot source.

For drive B to function as the boot source, a ﬂash memory card with software version 10.1 must be installed in drive B.

Image 19

Contents New Installation for NETBuilder II Software 95052-8145 3Com CorporationBayfront Plaza Santa Clara, CaliforniaContents CEC 20 System Index 3COM Corporation Limited Warranty Page Introduction About this GuideConvention Description ConventionsList conventions that are used throughout this guide Icon Alerts you toDesignated as drive a OverviewSoftware Installation ChecklistsChange the primary boot source default as needed Install System Software and Boot Refer to ChapterInstall software from a flash memory card Change the Primary Boot Source Refer to Chapter4CHAPTER 1 Overview Memory Card Installing Software and Booting DPE Netbuilder II SystemInstalling Software Performing Initial Boot Booting from the FlashNETBuilder II System Making a BackupFlash Memory CardFollowing these steps Using the BackupFlash Card Format the blank ﬂash memory card in drive B by enteringPage Changes Changing the Boot Source on aUsing the Boot CommandPrimary boot source Primary Boot SourceConﬁguring Configuring the Primary Boot Source Page CEC 20 Netbuilder II System Installing Software and BootingCD-ROM drive Installing SoftwareFrom a Network Management StationAt the network management station ProcedureTo see if these daemons are running, enter If you are using a Bourne sh or Korn ksh shell, enterTftp CD-ROM Station PrerequisitesStation Booting aNETBuilder II Image Over the NetworkImage/NBII/SW/101/FF/boot.29k To a Flash Memory Copying the SoftwareConﬁguring IP Format the blank ﬂash memory card by entering Enter a routing protocol For example, enable RIP usingPage You are now ready to enter software commands Slot 7 as the primary boot sourceFW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Logging on to Configuring Basic SettingsSystem User Interface Learning AboutInterface Main menu Level 1 is displayed Full-Form Syntax Reference for NETBuilder Family SoftwareSymbolDescription SymbolsAbbreviated Syntax Full and Abbreviated Syntax Examples Symbol DescriptionCan be abbreviated to Determining the Display of Ports and Virtual Ports Variations in Command SyntaxEntering Service Names in Command Lines Can be shortened by abbreviating it toCommand History Substitution Using AliasesDisplay it ﬁrst Privilege Level Strings Syntax for Assigning ValuesNumeric Values NamesPort and Path Naming Restrictions Media Addresses @22 Asynchronous Transfer Mode ATM addressDecimal. The Dlci identiﬁes a virtual circuit on the Frame An example of a Frame Relay addressNetwork Layer Addresses Addresses are the same 00003333%080002005678 For more information on Internet addresses, subnet masks,Followed by the MAC address Network from all other IPX networks. The following exampleDescribed in Table Getting HelpSyntax Description Manager Privilege Obtaining NetworkLevel Date PasswordSetting the Time ChangingAdministrator Setting SystemInformation Addresses to a Bridge Assigning InternetAddresses Assigning InternetSETDefault !2 -IP NETaddr = Internet addresses to individual ports using22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting from a Booting the Netbuilder II CEC a 20 System from the NetworkTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Technical Support ServicesService Access by Analog Modem408 654 2706 or 408 654 Access by Digital ModemPress Return to see the 3ComForum main menu 3Com Canada Regional Sales Office Telephone Number 3Com Corporation3Com Asia Limited Regional Sales Office Telephone Number 3Com Benelux B.VRegional Sales Office Telephone Number 3Com Mediterraneo Regional Sales Office Telephone Number 3Com Iberia3Com Ireland 3Com Latin AmericaNumerics Indexﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty