Casio P460 manual Required Tools, Environmental Prerequisites

Page 18

Chapter 3 Avaya P460 Chassis and Module Installation

Required Tools

You require the following equipment in order to install the P460 chassis:

Phillips (cross-blade) screwdriver

Environmental Prerequisites

Danger: To avoid injury, Avaya recommends that two people lift the switch onto a table top. A fully loaded P460 switch weighs at least 100 lbs (45 kg).

You can position the Avaya P460 in free-standing mode on a suitable shelf or table, or mount it in a standard 19-inch equipment rack in a wiring closet or equipment room.

When deciding where to position the chassis, ensure that:

It is accessible and cables can be connected easily and according to the configuration rule.

Cables are away from sources of electrical noise such as:

radio transmitters

broadcast amplifiers

power lines

fluorescent lighting fixtures.

Water or moisture cannot enter the case of the chassis.

There is a free flow of air around all sides the chassis.

The vents on the sides of the case are not blocked.

The table or shelf can hold the weight of the chassis with the PSUs and modules.

The environmental conditions match the requirements listed in Table 3.1. See Chapter 15, “Specifications“ for additional information.

Table 3.1

Environmental Requirements

 

 

Ambient temperature

23o to 122oF (-5oto 50oC)

Relative humidity

5% to 95%, non condensing

 

 

Minimum clearance for

2" (5 cm) on each side

ventilation

 

 

 

 

Weight support

50 lb. (23 kg) to 100 lbs (45 kg)

 

 

 

4

Avaya P460 Installation and Maintenance Guide

Image 18
Contents Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Before you Install the Avaya P460 Safety InformationPower Supplies FCC Notice Conventions Used in the DocumentationWarranty Avaya SupportCLI Conventions Preface Avaya P460 Installation and Maintenance Guide Avaya P460 Overview IntroductionFlexibility Avaya P460 Key FeaturesHigh Availability Management and MonitoringAvaya P460 Chassis and Module Installation Operating SafetyRequired Tools Environmental PrerequisitesAC Power Requirements Chassis Component Location KeyInstalling the P460 on a Table Top Rack Mounting140 mm P460 Rack mounting procedure Positioning the rack-mounting bracketsCable Guide Installation Installing the Cable GuidePSU Power Supply Unit Installation Fan Module Replacement or Installation Avaya P460 Switch Fan Module LocationInstalling the Avaya P460 Fan Module Supervisor Module Installation Location of the Avaya P460 Supervisor ModulesInstalling the P460 Supervisor Module Module Installation 10 Lcoation of Avaya P460 I/O ModulesModule Installation Procedure 11 I/O Module Component Location12 Installing P460 I/O Modules Installing a PSU Turning on the Avaya P460Turning on a Chassis with a Supervisor Module Only Powering UpInserting an Additional PSU Turning on a Chassis with no ModulesRemoving or Switching off a PSU If there is one PSUIf there are two PSUs If there are three PSUs Power Management Power Management ProcessI/O Module Power Management Process Avaya P460 Panels M460ML-SPV PanelM460ML-SPV LEDs PWR ACT LED and OPR LED Summary Starting Point After Power-up or Reset Function LEDsLNK LAG Eth Port Outband Connection M460ML-SPV Supervisor Module PortsM460ML-SPV Left and Right Pushbuttons RS-232 Port Sideband ConnectionM460ML-SPV ASB Alternate Software Bank Pushbutton P460 Supervisor Module ASB PushbuttonPower Supply Panel Page Maximizing Avaya P460 Availability M460ML-SPV Supervisor Module RedundancyM460ML-SPV Supervisor Module Modes Synchronizing the Supervisor Modules Manually Configuration File Synchronization Following screen capture shows the processMaximizing Avaya P460 Availability Redundant Power Supplies P460 show environment powerCalculating the Power Budget Sample Power Budget CalculationEstablishing Switch Access Establishing a Console Connection with the P460Establishing a Telnet Connection with the Switch Inband Inband Interface Connection CLI CommandsEstablishing a Telnet Connection with the Switch Outband M460ML-SPV Supervisor Module Fast Ethernet Console PortOutband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband ConnectionsSideband PPP Interface CLI Commands OverviewSetting Up Sideband PPP Connection Configuration Set interface ppp ipaddrnet-maskPage Avaya Msnm P460 Manager Running the Avaya Msnm P460 Manager WelcomeP460 Device Manager Install from the Avaya Web Site Installing the Java Plug-inInstalling from the P460 Documentation and Utilities CD Install from your Local Web SiteDocumentation Page User Authentication Access LevelsLocal User Accounts Local User Account CLI Commands Radius Introduction to RadiusIllustrates the Radius authentication procedure Radius CLI CommandsUser Authentication Allowed Manager CLI Commands Allowed ManagersConfiguration Defaults Default System ParametersConfiguration Default CLI Commands Basic Switch Configuration System Parameter Configuration Identifying the systemOperating parameters Time Parameter Configuration Feature License ConfigurationFeature Activation Obtaining a License Key Click Generate Feature License CLI Commands Activating a Routing License KeyPowering up the Supervisor Modules Troubleshooting the InstallationPowering up the Chassis Powering up the Fan ModulePowering up the I/O Modules Supervisor Module does not Boot Page Two Supervisor Modules in the Switch MaintenanceOne Supervisor Module in the Switch Replacing I/O ModulesFirmware Download IntroductionPreferred Bank Configuration File Management Firmware Download CLI CommandsConfiguration Management CLI Commands Page Standards IeeeRouting Specifications PhysicalPower Requirements SafetyEnvironmental EMC Emissions ImmunityTransportation Catalog Numbers Avaya P460 Catalog Numbers