Casio P460 manual M460ML-SPV Supervisor Module Ports, M460ML-SPV Left and Right Pushbuttons

Page 45

Chapter 5 Avaya P460 Panels

M460ML-SPV Supervisor Module Ports

Figure 5.4 M460ML-SPV Supervisor Module Console Ports

12

Key

1Eth (Ethernet) Port

2RS-232 (Serial) port

Eth Port (Outband Connection)

A10/100BASE-T port with an RJ-45 connector for managing the P460 by a dedicated LAN.

RS-232 Port (Sideband Connection)

An RJ-45 RS-232 serial port for connecting a modem or terminal for configuration with the CLI.

M460ML-SPV Left and Right Pushbuttons

Figure 5.5 P460 Supervisor Module Left and Right Pushbutton

1 2

Key

1L (Left) pushbutton

2R (Right) pushbutton

	Table 5.7	M460ML-SPV Left and Right Pushbutton Functions

	To...		Press...


	Cycle between the Function LEDs.		The Left or Right button briefly.
	See “Function LEDs“ on page 28
	for further information

	Reset the Supervisor Module		Both buttons at the same time for 1.5
			seconds.

	Reset the chassis		Both buttons at the same time for five
			seconds.

Avaya P460 Installation and Maintenance Guide

31

Image 45

Contents Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Before you Install the Avaya P460 Safety InformationPower Supplies Conventions Used in the Documentation FCC NoticeWarranty Avaya SupportCLI Conventions Preface Avaya P460 Installation and Maintenance Guide Introduction Avaya P460 OverviewHigh Availability Avaya P460 Key FeaturesFlexibility Management and MonitoringOperating Safety Avaya P460 Chassis and Module InstallationEnvironmental Prerequisites Required ToolsAC Power Requirements Key Chassis Component LocationRack Mounting Installing the P460 on a Table Top140 mm Positioning the rack-mounting brackets P460 Rack mounting procedureInstalling the Cable Guide Cable Guide InstallationPSU Power Supply Unit Installation Avaya P460 Switch Fan Module Location Fan Module Replacement or InstallationInstalling the Avaya P460 Fan Module Location of the Avaya P460 Supervisor Modules Supervisor Module InstallationInstalling the P460 Supervisor Module 10 Lcoation of Avaya P460 I/O Modules Module Installation11 I/O Module Component Location Module Installation Procedure12 Installing P460 I/O Modules Turning on the Avaya P460 Installing a PSUInserting an Additional PSU Powering UpTurning on a Chassis with a Supervisor Module Only Turning on a Chassis with no ModulesRemoving or Switching off a PSU If there is one PSUIf there are two PSUs If there are three PSUs Power Management Process Power ManagementI/O Module Power Management Process Avaya P460 Panels M460ML-SPV PanelM460ML-SPV LEDs PWR ACT LED and OPR LED Summary Function LEDs Starting Point After Power-up or ResetLNK LAG M460ML-SPV Left and Right Pushbuttons M460ML-SPV Supervisor Module PortsEth Port Outband Connection RS-232 Port Sideband ConnectionP460 Supervisor Module ASB Pushbutton M460ML-SPV ASB Alternate Software Bank PushbuttonPower Supply Panel Page Maximizing Avaya P460 Availability M460ML-SPV Supervisor Module RedundancyM460ML-SPV Supervisor Module Modes Synchronizing the Supervisor Modules Manually Following screen capture shows the process Configuration File SynchronizationMaximizing Avaya P460 Availability P460 show environment power Redundant Power SuppliesSample Power Budget Calculation Calculating the Power BudgetEstablishing a Console Connection with the P460 Establishing Switch AccessInband Interface Connection CLI Commands Establishing a Telnet Connection with the Switch InbandM460ML-SPV Supervisor Module Fast Ethernet Console Port Establishing a Telnet Connection with the Switch OutbandOutband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband ConnectionsOverview Sideband PPP Interface CLI CommandsSet interface ppp ipaddrnet-mask Setting Up Sideband PPP Connection ConfigurationPage Avaya Msnm P460 Manager Welcome Running the Avaya Msnm P460 ManagerP460 Device Manager Installing from the P460 Documentation and Utilities CD Installing the Java Plug-inInstall from the Avaya Web Site Install from your Local Web SiteDocumentation Page User Authentication Access LevelsLocal User Accounts Local User Account CLI Commands Introduction to Radius RadiusRadius CLI Commands Illustrates the Radius authentication procedureUser Authentication Allowed Managers Allowed Manager CLI CommandsDefault System Parameters Configuration DefaultsConfiguration Default CLI Commands Basic Switch Configuration System Parameter Configuration Identifying the systemOperating parameters Time Parameter Configuration Feature License ConfigurationFeature Activation Obtaining a License Key Click Generate Activating a Routing License Key Feature License CLI CommandsPowering up the Chassis Troubleshooting the InstallationPowering up the Supervisor Modules Powering up the Fan ModulePowering up the I/O Modules Supervisor Module does not Boot Page One Supervisor Module in the Switch MaintenanceTwo Supervisor Modules in the Switch Replacing I/O ModulesFirmware Download IntroductionPreferred Bank Configuration File Management Firmware Download CLI CommandsConfiguration Management CLI Commands Page Ieee StandardsRouting Physical SpecificationsPower Requirements SafetyEnvironmental EMC Emissions ImmunityTransportation Avaya P460 Catalog Numbers Catalog Numbers