Casio P460 manual Configuration Defaults, Default System Parameters

Page 75

Chapter 10

Configuration Defaults

Introduction

This chapter defines the default parameters for the P460 switch.

Default System Parameters

Table 10.1 Default System Parameters

Parameter	Default Value


All IP addresses	N/A (0.0.0.0)

Default gateway	N/A (0.0.0.0)

CLI timeout	15 minutes

User name	root

Password	root

PPP interface	Disabled

Out-of-band interface	Disabled

In-band interface	Disabled

In-band ARP Tx interval	5 seconds

Out-of-band ARP Tx interval	5 seconds

VLANs	1 on all ports

Spanning Tree	Enabled

Bridge priority for Spanning Tree	32,768

NTP server IP address	N/A

Time zone offset	0 hours

Timezone	GMT

Read-only SNMP community string	public

Avaya P460 Installation and Maintenance Guide

61

Image 75

Contents Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Before you Install the Avaya P460 Safety InformationPower Supplies Conventions Used in the Documentation FCC NoticeWarranty Avaya SupportCLI Conventions Preface Avaya P460 Installation and Maintenance Guide Introduction Avaya P460 OverviewManagement and Monitoring Avaya P460 Key FeaturesHigh Availability FlexibilityOperating Safety Avaya P460 Chassis and Module InstallationEnvironmental Prerequisites Required ToolsAC Power Requirements Key Chassis Component LocationRack Mounting Installing the P460 on a Table Top140 mm Positioning the rack-mounting brackets P460 Rack mounting procedureInstalling the Cable Guide Cable Guide InstallationPSU Power Supply Unit Installation Avaya P460 Switch Fan Module Location Fan Module Replacement or InstallationInstalling the Avaya P460 Fan Module Location of the Avaya P460 Supervisor Modules Supervisor Module InstallationInstalling the P460 Supervisor Module 10 Lcoation of Avaya P460 I/O Modules Module Installation11 I/O Module Component Location Module Installation Procedure12 Installing P460 I/O Modules Turning on the Avaya P460 Installing a PSUTurning on a Chassis with no Modules Powering UpInserting an Additional PSU Turning on a Chassis with a Supervisor Module OnlyRemoving or Switching off a PSU If there is one PSUIf there are two PSUs If there are three PSUs Power Management Process Power ManagementI/O Module Power Management Process Avaya P460 Panels M460ML-SPV PanelM460ML-SPV LEDs PWR ACT LED and OPR LED Summary Function LEDs Starting Point After Power-up or ResetLNK LAG RS-232 Port Sideband Connection M460ML-SPV Supervisor Module PortsM460ML-SPV Left and Right Pushbuttons Eth Port Outband ConnectionP460 Supervisor Module ASB Pushbutton M460ML-SPV ASB Alternate Software Bank PushbuttonPower Supply Panel Page Maximizing Avaya P460 Availability M460ML-SPV Supervisor Module RedundancyM460ML-SPV Supervisor Module Modes Synchronizing the Supervisor Modules Manually Following screen capture shows the process Configuration File SynchronizationMaximizing Avaya P460 Availability P460 show environment power Redundant Power SuppliesSample Power Budget Calculation Calculating the Power BudgetEstablishing a Console Connection with the P460 Establishing Switch AccessInband Interface Connection CLI Commands Establishing a Telnet Connection with the Switch InbandM460ML-SPV Supervisor Module Fast Ethernet Console Port Establishing a Telnet Connection with the Switch OutbandOutband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband ConnectionsOverview Sideband PPP Interface CLI CommandsSet interface ppp ipaddrnet-mask Setting Up Sideband PPP Connection ConfigurationPage Avaya Msnm P460 Manager Welcome Running the Avaya Msnm P460 ManagerP460 Device Manager Install from your Local Web Site Installing the Java Plug-inInstalling from the P460 Documentation and Utilities CD Install from the Avaya Web SiteDocumentation Page User Authentication Access LevelsLocal User Accounts Local User Account CLI Commands Introduction to Radius RadiusRadius CLI Commands Illustrates the Radius authentication procedureUser Authentication Allowed Managers Allowed Manager CLI CommandsDefault System Parameters Configuration DefaultsConfiguration Default CLI Commands Basic Switch Configuration System Parameter Configuration Identifying the systemOperating parameters Time Parameter Configuration Feature License ConfigurationFeature Activation Obtaining a License Key Click Generate Activating a Routing License Key Feature License CLI CommandsPowering up the Fan Module Troubleshooting the InstallationPowering up the Chassis Powering up the Supervisor ModulesPowering up the I/O Modules Supervisor Module does not Boot Page Replacing I/O Modules MaintenanceOne Supervisor Module in the Switch Two Supervisor Modules in the SwitchFirmware Download IntroductionPreferred Bank Configuration File Management Firmware Download CLI CommandsConfiguration Management CLI Commands Page Ieee StandardsRouting Physical SpecificationsPower Requirements SafetyEnvironmental EMC Emissions ImmunityTransportation Avaya P460 Catalog Numbers Catalog Numbers