Casio P460 manual Configuration File Management, Firmware Download CLI Commands

Page 89

		Chapter 13	Maintenance

Firmware Download CLI Commands

	In order to...	Use the following command...


	Set the default boot bank	set boot bank

	Download firmware to Bank A	copy tftp SW_imageA

	Download firmware to Bank B	copy tftp SW_imageB

	Copy Device Manager (Embedded	copy tftp EW_archive
	Web) firmware

	Show the default boot bank	show boot bank

Configuration File Management

You can transfer the Layer 2 parameters to or from the current NVRAM running configuration file to a TFTP server.

This feature permits you to make a backup of the parameters. You can then use that file to configure other Avaya P460 switches without re-entering all the parameters manually.

To use this feature, you need to have an active tftp server, and to create a file into which to download the data.

If Avaya MultiService Network Manager is running, you do not require an additional TFTP server.

Configuration Management CLI Commands

In order to...	Use the following command...


Upload the Layer 2 parameters	copy l2-config tftp
from the current NVRAM running
configuration to a file via TFTP

Update the Layer 2 parameters in	copy tftp l2-config
the current NVRAM running
configuration from a file via TFTP

Show the Layer 2 configuration file	show l2-config

Avaya P460 Installation and Maintenance Guide

75

Image 89

Contents Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Power Supplies Before you Install the Avaya P460Safety Information Conventions Used in the Documentation FCC NoticeCLI Conventions WarrantyAvaya Support Preface Avaya P460 Installation and Maintenance Guide Introduction Avaya P460 OverviewHigh Availability Avaya P460 Key FeaturesFlexibility Management and MonitoringOperating Safety Avaya P460 Chassis and Module InstallationEnvironmental Prerequisites Required ToolsAC Power Requirements Key Chassis Component LocationRack Mounting Installing the P460 on a Table Top140 mm Positioning the rack-mounting brackets P460 Rack mounting procedureInstalling the Cable Guide Cable Guide InstallationPSU Power Supply Unit Installation Avaya P460 Switch Fan Module Location Fan Module Replacement or InstallationInstalling the Avaya P460 Fan Module Location of the Avaya P460 Supervisor Modules Supervisor Module InstallationInstalling the P460 Supervisor Module 10 Lcoation of Avaya P460 I/O Modules Module Installation11 I/O Module Component Location Module Installation Procedure12 Installing P460 I/O Modules Turning on the Avaya P460 Installing a PSUInserting an Additional PSU Powering UpTurning on a Chassis with a Supervisor Module Only Turning on a Chassis with no ModulesIf there are two PSUs Removing or Switching off a PSUIf there is one PSU If there are three PSUs Power Management Process Power ManagementI/O Module Power Management Process M460ML-SPV LEDs Avaya P460 PanelsM460ML-SPV Panel PWR ACT LED and OPR LED Summary Function LEDs Starting Point After Power-up or ResetLNK LAG M460ML-SPV Left and Right Pushbuttons M460ML-SPV Supervisor Module PortsEth Port Outband Connection RS-232 Port Sideband ConnectionP460 Supervisor Module ASB Pushbutton M460ML-SPV ASB Alternate Software Bank PushbuttonPower Supply Panel Page M460ML-SPV Supervisor Module Modes Maximizing Avaya P460 AvailabilityM460ML-SPV Supervisor Module Redundancy Synchronizing the Supervisor Modules Manually Following screen capture shows the process Configuration File SynchronizationMaximizing Avaya P460 Availability P460 show environment power Redundant Power SuppliesSample Power Budget Calculation Calculating the Power BudgetEstablishing a Console Connection with the P460 Establishing Switch AccessInband Interface Connection CLI Commands Establishing a Telnet Connection with the Switch InbandM460ML-SPV Supervisor Module Fast Ethernet Console Port Establishing a Telnet Connection with the Switch OutbandOutband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband ConnectionsOverview Sideband PPP Interface CLI CommandsSet interface ppp ipaddrnet-mask Setting Up Sideband PPP Connection ConfigurationPage Avaya Msnm P460 Manager Welcome Running the Avaya Msnm P460 ManagerP460 Device Manager Installing from the P460 Documentation and Utilities CD Installing the Java Plug-inInstall from the Avaya Web Site Install from your Local Web SiteDocumentation Page Local User Accounts User AuthenticationAccess Levels Local User Account CLI Commands Introduction to Radius RadiusRadius CLI Commands Illustrates the Radius authentication procedureUser Authentication Allowed Managers Allowed Manager CLI CommandsDefault System Parameters Configuration DefaultsConfiguration Default CLI Commands Basic Switch Configuration Operating parameters System Parameter ConfigurationIdentifying the system Feature Activation Time Parameter ConfigurationFeature License Configuration Obtaining a License Key Click Generate Activating a Routing License Key Feature License CLI CommandsPowering up the Chassis Troubleshooting the InstallationPowering up the Supervisor Modules Powering up the Fan ModulePowering up the I/O Modules Supervisor Module does not Boot Page One Supervisor Module in the Switch MaintenanceTwo Supervisor Modules in the Switch Replacing I/O ModulesPreferred Bank Firmware DownloadIntroduction Configuration Management CLI Commands Configuration File ManagementFirmware Download CLI Commands Page Ieee StandardsRouting Physical SpecificationsEnvironmental Power RequirementsSafety Transportation EMC EmissionsImmunity Avaya P460 Catalog Numbers Catalog Numbers