Casio manual Module Installation, Lcoation of Avaya P460 I/O Modules

Page 30

Chapter 3 Avaya P460 Chassis and Module Installation

I/O Module Installation

If you purchased an Avaya P460ML-CFG (Material code 700255003, PEC Code 4548-009), then one Supervisor Module, PSU and the Fan Module are already installed.

Figure 3.10 shows the positions of I/O modules installed in the P460 chassis.

Figure 3.10 Lcoation of Avaya P460 I/O Modules

You can install I/O modules in the bottom four slots – 3 to 6 – only.

Caution: Do not leave any slots open. Use the the blanking plates supplied to cover empty slots.

Caution: The I/O modules contain components that are sensitive to static discharge. Handle the module by the edges only.

Use appropriate anti-static equipment when handling the switch and modules.

16

Avaya P460 Installation and Maintenance Guide

Image 30
Contents Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Before you Install the Avaya P460 Safety InformationPower Supplies FCC Notice Conventions Used in the DocumentationWarranty Avaya SupportCLI Conventions Preface Avaya P460 Installation and Maintenance Guide Avaya P460 Overview IntroductionFlexibility Avaya P460 Key FeaturesHigh Availability Management and MonitoringAvaya P460 Chassis and Module Installation Operating SafetyRequired Tools Environmental PrerequisitesAC Power Requirements Chassis Component Location KeyInstalling the P460 on a Table Top Rack Mounting140 mm P460 Rack mounting procedure Positioning the rack-mounting bracketsCable Guide Installation Installing the Cable GuidePSU Power Supply Unit Installation Fan Module Replacement or Installation Avaya P460 Switch Fan Module LocationInstalling the Avaya P460 Fan Module Supervisor Module Installation Location of the Avaya P460 Supervisor ModulesInstalling the P460 Supervisor Module Module Installation 10 Lcoation of Avaya P460 I/O ModulesModule Installation Procedure 11 I/O Module Component Location12 Installing P460 I/O Modules Installing a PSU Turning on the Avaya P460Turning on a Chassis with a Supervisor Module Only Powering UpInserting an Additional PSU Turning on a Chassis with no ModulesRemoving or Switching off a PSU If there is one PSUIf there are two PSUs If there are three PSUs Power Management Power Management ProcessI/O Module Power Management Process Avaya P460 Panels M460ML-SPV PanelM460ML-SPV LEDs PWR ACT LED and OPR LED Summary Starting Point After Power-up or Reset Function LEDsLNK LAG Eth Port Outband Connection M460ML-SPV Supervisor Module PortsM460ML-SPV Left and Right Pushbuttons RS-232 Port Sideband ConnectionM460ML-SPV ASB Alternate Software Bank Pushbutton P460 Supervisor Module ASB PushbuttonPower Supply Panel Page Maximizing Avaya P460 Availability M460ML-SPV Supervisor Module RedundancyM460ML-SPV Supervisor Module Modes Synchronizing the Supervisor Modules Manually Configuration File Synchronization Following screen capture shows the processMaximizing Avaya P460 Availability Redundant Power Supplies P460 show environment powerCalculating the Power Budget Sample Power Budget CalculationEstablishing Switch Access Establishing a Console Connection with the P460Establishing a Telnet Connection with the Switch Inband Inband Interface Connection CLI CommandsEstablishing a Telnet Connection with the Switch Outband M460ML-SPV Supervisor Module Fast Ethernet Console PortOutband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband ConnectionsSideband PPP Interface CLI Commands OverviewSetting Up Sideband PPP Connection Configuration Set interface ppp ipaddrnet-maskPage Avaya Msnm P460 Manager Running the Avaya Msnm P460 Manager WelcomeP460 Device Manager Install from the Avaya Web Site Installing the Java Plug-inInstalling from the P460 Documentation and Utilities CD Install from your Local Web SiteDocumentation Page User Authentication Access LevelsLocal User Accounts Local User Account CLI Commands Radius Introduction to RadiusIllustrates the Radius authentication procedure Radius CLI CommandsUser Authentication Allowed Manager CLI Commands Allowed ManagersConfiguration Defaults Default System ParametersConfiguration Default CLI Commands Basic Switch Configuration System Parameter Configuration Identifying the systemOperating parameters Time Parameter Configuration Feature License ConfigurationFeature Activation Obtaining a License Key Click Generate Feature License CLI Commands Activating a Routing License KeyPowering up the Supervisor Modules Troubleshooting the InstallationPowering up the Chassis Powering up the Fan ModulePowering up the I/O Modules Supervisor Module does not Boot Page Two Supervisor Modules in the Switch MaintenanceOne Supervisor Module in the Switch Replacing I/O ModulesFirmware Download IntroductionPreferred Bank Configuration File Management Firmware Download CLI CommandsConfiguration Management CLI Commands Page Standards IeeeRouting Specifications PhysicalPower Requirements SafetyEnvironmental EMC Emissions ImmunityTransportation Catalog Numbers Avaya P460 Catalog Numbers