Casio P460 manual Lnk

Page 43

Chapter 5 Avaya P460 Panels

Note: Press both buttons simultaneously for 1.5 seconds to reset the SPV supervisor module.

Press both switches simultaneously for five seconds to reset the entire switch. Refer to "M460ML-SPV Left and Right Pushbuttons" on page 31 for full details of reset options.

Table 5.6 summarizes the meanings of the function LEDs. Certain indications depend on the specific I/O module port type:

Table 5.6	M460ML-SPV Function LEDs

LED	Description	State	Meaning


LNK	Port status	ON	Port enabled and link OK

		OFF	Port disabled or link is not
			operating

COL	Collision detection	ON	Collision occurred on line

		OFF	No collision or FDX port

Tx	Transmit to line	ON	Data transmitted to the line

		OFF	No transmit activity

Rx	Receive from line	ON	Data received from the line

		OFF	No receive activity

FDX	Full-/Half-duplex	ON	Full-duplex mode
	Indication		For 10/100BASE-T ports when
			the link test fails with auto-
			negotiation enabled

		OFF	Half-duplex mode

FC	Flow Control	ON	Flow Control is active

		OFF	Flow Control is disabled

HSpd	Port speed indication	ON	Port	10/100	1000
				100 Mbps 1000 Mbps

		OFF	Port	10/100	1000
				10 Mbps	N/A

Avaya P460 Installation and Maintenance Guide

29

Image 43

Contents Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Safety Information Before you Install the Avaya P460Power Supplies Conventions Used in the Documentation FCC NoticeAvaya Support WarrantyCLI Conventions Preface Avaya P460 Installation and Maintenance Guide Introduction Avaya P460 OverviewManagement and Monitoring Avaya P460 Key FeaturesHigh Availability FlexibilityOperating Safety Avaya P460 Chassis and Module InstallationEnvironmental Prerequisites Required ToolsAC Power Requirements Key Chassis Component LocationRack Mounting Installing the P460 on a Table Top140 mm Positioning the rack-mounting brackets P460 Rack mounting procedureInstalling the Cable Guide Cable Guide InstallationPSU Power Supply Unit Installation Avaya P460 Switch Fan Module Location Fan Module Replacement or InstallationInstalling the Avaya P460 Fan Module Location of the Avaya P460 Supervisor Modules Supervisor Module InstallationInstalling the P460 Supervisor Module 10 Lcoation of Avaya P460 I/O Modules Module Installation11 I/O Module Component Location Module Installation Procedure12 Installing P460 I/O Modules Turning on the Avaya P460 Installing a PSUTurning on a Chassis with no Modules Powering UpInserting an Additional PSU Turning on a Chassis with a Supervisor Module OnlyIf there is one PSU Removing or Switching off a PSUIf there are two PSUs If there are three PSUs Power Management Process Power ManagementI/O Module Power Management Process M460ML-SPV Panel Avaya P460 PanelsM460ML-SPV LEDs PWR ACT LED and OPR LED Summary Function LEDs Starting Point After Power-up or ResetLNK LAG RS-232 Port Sideband Connection M460ML-SPV Supervisor Module PortsM460ML-SPV Left and Right Pushbuttons Eth Port Outband ConnectionP460 Supervisor Module ASB Pushbutton M460ML-SPV ASB Alternate Software Bank PushbuttonPower Supply Panel Page M460ML-SPV Supervisor Module Redundancy Maximizing Avaya P460 AvailabilityM460ML-SPV Supervisor Module Modes Synchronizing the Supervisor Modules Manually Following screen capture shows the process Configuration File SynchronizationMaximizing Avaya P460 Availability P460 show environment power Redundant Power SuppliesSample Power Budget Calculation Calculating the Power BudgetEstablishing a Console Connection with the P460 Establishing Switch AccessInband Interface Connection CLI Commands Establishing a Telnet Connection with the Switch InbandM460ML-SPV Supervisor Module Fast Ethernet Console Port Establishing a Telnet Connection with the Switch OutbandOutband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband ConnectionsOverview Sideband PPP Interface CLI CommandsSet interface ppp ipaddrnet-mask Setting Up Sideband PPP Connection ConfigurationPage Avaya Msnm P460 Manager Welcome Running the Avaya Msnm P460 ManagerP460 Device Manager Install from your Local Web Site Installing the Java Plug-inInstalling from the P460 Documentation and Utilities CD Install from the Avaya Web SiteDocumentation Page Access Levels User AuthenticationLocal User Accounts Local User Account CLI Commands Introduction to Radius RadiusRadius CLI Commands Illustrates the Radius authentication procedureUser Authentication Allowed Managers Allowed Manager CLI CommandsDefault System Parameters Configuration DefaultsConfiguration Default CLI Commands Basic Switch Configuration Identifying the system System Parameter ConfigurationOperating parameters Feature License Configuration Time Parameter ConfigurationFeature Activation Obtaining a License Key Click Generate Activating a Routing License Key Feature License CLI CommandsPowering up the Fan Module Troubleshooting the InstallationPowering up the Chassis Powering up the Supervisor ModulesPowering up the I/O Modules Supervisor Module does not Boot Page Replacing I/O Modules MaintenanceOne Supervisor Module in the Switch Two Supervisor Modules in the SwitchIntroduction Firmware DownloadPreferred Bank Firmware Download CLI Commands Configuration File ManagementConfiguration Management CLI Commands Page Ieee StandardsRouting Physical SpecificationsSafety Power RequirementsEnvironmental Immunity EMC EmissionsTransportation Avaya P460 Catalog Numbers Catalog Numbers