Casio manual Installing the P460 Supervisor Module

Page 29

Chapter 3 Avaya P460 Chassis and Module Installation

Figure 3.9 Installing the P460 Supervisor Module

a3

b

Key

aOpen locking handle

bClosed locking handle

To install a Supervisor module:

1Remove the blanking plate or installed module as appropriate.

2Open the locking handles at the edge of the front panel.

3Position the module in the slot as shown in Figure 3.9.

4Gently slide the module in.

Ensure the hooks on the locking handle are aligned with the matching holes on the chassis.

5Close the locking handles.

XThe module slides back and connects to the backplane.

6 Gently tighten the screws.

For information on configuring redundant supervisor modules, refer to “M460ML-SPV Supervisor Module Redundancy“ on page 35.

Avaya P460 Installation and Maintenance Guide

15

Image 29

Contents Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Power Supplies Before you Install the Avaya P460Safety Information Conventions Used in the Documentation FCC NoticeCLI Conventions WarrantyAvaya Support Preface Avaya P460 Installation and Maintenance Guide Introduction Avaya P460 OverviewHigh Availability Avaya P460 Key FeaturesFlexibility Management and MonitoringOperating Safety Avaya P460 Chassis and Module InstallationEnvironmental Prerequisites Required ToolsAC Power Requirements Key Chassis Component LocationRack Mounting Installing the P460 on a Table Top140 mm Positioning the rack-mounting brackets P460 Rack mounting procedureInstalling the Cable Guide Cable Guide InstallationPSU Power Supply Unit Installation Avaya P460 Switch Fan Module Location Fan Module Replacement or InstallationInstalling the Avaya P460 Fan Module Location of the Avaya P460 Supervisor Modules Supervisor Module InstallationInstalling the P460 Supervisor Module 10 Lcoation of Avaya P460 I/O Modules Module Installation11 I/O Module Component Location Module Installation Procedure12 Installing P460 I/O Modules Turning on the Avaya P460 Installing a PSUInserting an Additional PSU Powering UpTurning on a Chassis with a Supervisor Module Only Turning on a Chassis with no ModulesIf there are two PSUs Removing or Switching off a PSUIf there is one PSU If there are three PSUs Power Management Process Power ManagementI/O Module Power Management Process M460ML-SPV LEDs Avaya P460 PanelsM460ML-SPV Panel PWR ACT LED and OPR LED Summary Function LEDs Starting Point After Power-up or ResetLNK LAG M460ML-SPV Left and Right Pushbuttons M460ML-SPV Supervisor Module PortsEth Port Outband Connection RS-232 Port Sideband ConnectionP460 Supervisor Module ASB Pushbutton M460ML-SPV ASB Alternate Software Bank PushbuttonPower Supply Panel Page M460ML-SPV Supervisor Module Modes Maximizing Avaya P460 AvailabilityM460ML-SPV Supervisor Module Redundancy Synchronizing the Supervisor Modules Manually Following screen capture shows the process Configuration File SynchronizationMaximizing Avaya P460 Availability P460 show environment power Redundant Power SuppliesSample Power Budget Calculation Calculating the Power BudgetEstablishing a Console Connection with the P460 Establishing Switch AccessInband Interface Connection CLI Commands Establishing a Telnet Connection with the Switch InbandM460ML-SPV Supervisor Module Fast Ethernet Console Port Establishing a Telnet Connection with the Switch OutbandOutband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband ConnectionsOverview Sideband PPP Interface CLI CommandsSet interface ppp ipaddrnet-mask Setting Up Sideband PPP Connection ConfigurationPage Avaya Msnm P460 Manager Welcome Running the Avaya Msnm P460 ManagerP460 Device Manager Installing from the P460 Documentation and Utilities CD Installing the Java Plug-inInstall from the Avaya Web Site Install from your Local Web SiteDocumentation Page Local User Accounts User AuthenticationAccess Levels Local User Account CLI Commands Introduction to Radius RadiusRadius CLI Commands Illustrates the Radius authentication procedureUser Authentication Allowed Managers Allowed Manager CLI CommandsDefault System Parameters Configuration DefaultsConfiguration Default CLI Commands Basic Switch Configuration Operating parameters System Parameter ConfigurationIdentifying the system Feature Activation Time Parameter ConfigurationFeature License Configuration Obtaining a License Key Click Generate Activating a Routing License Key Feature License CLI CommandsPowering up the Chassis Troubleshooting the InstallationPowering up the Supervisor Modules Powering up the Fan ModulePowering up the I/O Modules Supervisor Module does not Boot Page One Supervisor Module in the Switch MaintenanceTwo Supervisor Modules in the Switch Replacing I/O ModulesPreferred Bank Firmware DownloadIntroduction Configuration Management CLI Commands Configuration File ManagementFirmware Download CLI Commands Page Ieee StandardsRouting Physical SpecificationsEnvironmental Power RequirementsSafety Transportation EMC EmissionsImmunity Avaya P460 Catalog Numbers Catalog Numbers