Casio P460 Setting Up Sideband PPP Connection Configuration, Set interface ppp ipaddrnet-mask

Page 61

Chapter 7 Establishing Switch Access

Setting Up Sideband (PPP) Connection Configuration

You need to configure an IP address and netmask for the sideband interface before you can establish a ppp link.

1Connect a terminal to the Serial console port.

2When you are prompted for a Login Name, enter the default name root.

3When you are prompted for a password, enter the password root. You are now in Supervisor Level.

4At the prompt, type:

set interface ppp <ip_addr><net-mask>

with an IP address and netmask to be used by the Avaya P460 Supervisor module to connect via its PPP interface.

The PPP interface you configure with the set interface ppp command must be on a different subnet from the inband and outband interfaces.

5Set the baud rate, ppp authentication, and ppp time out required to match your modem.

6At the prompt, type:

set interface ppp enable

XThe following is displayed:

Entering the Modem mode within 60 seconds...

Please check that the proprietary modem cable is plugged into the console port

7Use the DB-25 to RJ-45 connector to plug the console cable to the modem’s DB- 25 connector. Plug the other end of the cable RJ-45 connector to an

Avaya P460 Supervisor module RJ-45 port.

8The Avaya P460 Supervisor module enters modem mode.

9You can now dial into the switch from a remote station, and open a Telnet, ping or SNMP management session to the PPP interface IP address.

If you have two Supervisor modules installed, you can make a serial connection to one SPV and configure the PPP parameters through one session and deploy the PPP connection on the second Supervisor module.

Avaya P460 Installation and Maintenance Guide

47

Image 61

Contents Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Safety Information Before you Install the Avaya P460Power Supplies Conventions Used in the Documentation FCC NoticeAvaya Support WarrantyCLI Conventions Preface Avaya P460 Installation and Maintenance Guide Introduction Avaya P460 OverviewHigh Availability Avaya P460 Key FeaturesFlexibility Management and MonitoringOperating Safety Avaya P460 Chassis and Module InstallationEnvironmental Prerequisites Required ToolsAC Power Requirements Key Chassis Component LocationRack Mounting Installing the P460 on a Table Top140 mm Positioning the rack-mounting brackets P460 Rack mounting procedureInstalling the Cable Guide Cable Guide InstallationPSU Power Supply Unit Installation Avaya P460 Switch Fan Module Location Fan Module Replacement or InstallationInstalling the Avaya P460 Fan Module Location of the Avaya P460 Supervisor Modules Supervisor Module InstallationInstalling the P460 Supervisor Module 10 Lcoation of Avaya P460 I/O Modules Module Installation11 I/O Module Component Location Module Installation Procedure12 Installing P460 I/O Modules Turning on the Avaya P460 Installing a PSUInserting an Additional PSU Powering UpTurning on a Chassis with a Supervisor Module Only Turning on a Chassis with no ModulesIf there is one PSU Removing or Switching off a PSUIf there are two PSUs If there are three PSUs Power Management Process Power ManagementI/O Module Power Management Process M460ML-SPV Panel Avaya P460 PanelsM460ML-SPV LEDs PWR ACT LED and OPR LED Summary Function LEDs Starting Point After Power-up or ResetLNK LAG M460ML-SPV Left and Right Pushbuttons M460ML-SPV Supervisor Module PortsEth Port Outband Connection RS-232 Port Sideband ConnectionP460 Supervisor Module ASB Pushbutton M460ML-SPV ASB Alternate Software Bank PushbuttonPower Supply Panel Page M460ML-SPV Supervisor Module Redundancy Maximizing Avaya P460 AvailabilityM460ML-SPV Supervisor Module Modes Synchronizing the Supervisor Modules Manually Following screen capture shows the process Configuration File SynchronizationMaximizing Avaya P460 Availability P460 show environment power Redundant Power SuppliesSample Power Budget Calculation Calculating the Power BudgetEstablishing a Console Connection with the P460 Establishing Switch AccessInband Interface Connection CLI Commands Establishing a Telnet Connection with the Switch InbandM460ML-SPV Supervisor Module Fast Ethernet Console Port Establishing a Telnet Connection with the Switch OutbandOutband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband ConnectionsOverview Sideband PPP Interface CLI CommandsSet interface ppp ipaddrnet-mask Setting Up Sideband PPP Connection ConfigurationPage Avaya Msnm P460 Manager Welcome Running the Avaya Msnm P460 ManagerP460 Device Manager Installing from the P460 Documentation and Utilities CD Installing the Java Plug-inInstall from the Avaya Web Site Install from your Local Web SiteDocumentation Page Access Levels User AuthenticationLocal User Accounts Local User Account CLI Commands Introduction to Radius RadiusRadius CLI Commands Illustrates the Radius authentication procedureUser Authentication Allowed Managers Allowed Manager CLI CommandsDefault System Parameters Configuration DefaultsConfiguration Default CLI Commands Basic Switch Configuration Identifying the system System Parameter ConfigurationOperating parameters Feature License Configuration Time Parameter ConfigurationFeature Activation Obtaining a License Key Click Generate Activating a Routing License Key Feature License CLI CommandsPowering up the Chassis Troubleshooting the InstallationPowering up the Supervisor Modules Powering up the Fan ModulePowering up the I/O Modules Supervisor Module does not Boot Page One Supervisor Module in the Switch MaintenanceTwo Supervisor Modules in the Switch Replacing I/O ModulesIntroduction Firmware DownloadPreferred Bank Firmware Download CLI Commands Configuration File ManagementConfiguration Management CLI Commands Page Ieee StandardsRouting Physical SpecificationsSafety Power RequirementsEnvironmental Immunity EMC EmissionsTransportation Avaya P460 Catalog Numbers Catalog Numbers