Casio P460 manual 11 I/O Module Component Location, Module Installation Procedure

Page 31

Chapter 3 Avaya P460 Chassis and Module Installation

Figure 3.11 I/O Module Component Location

	1
2	2
3	3

Key

1Module label

2Securing screws

3Locking handles

I/O Module Installation Procedure

To install an I/O module:

1Remove the blanking plate by unscrewing the captive screws and gently pulling the plate towards you.

2Open the locking handles at the edge of the front panel. See Figure 3.12.

3Position the module as shown in Figure 3.12.

4Gently slide the module in.

Ensure the hooks on the locking handle are aligned with the matching holes on the chassis.

5Close the locking handles.

XThe module slides back and connects to the backplane.

6 Gently tighten the screws.

For module-specific information, refer to the Installation Guide shipped with the module.

Avaya P460 Installation and Maintenance Guide

17

Image 31

Contents Avaya P460 Page Contents Table of Contents Radius Ieee Ietf List of Tables List of Tables Avaya P460 Installation and Maintenance Guide List of Figures Page Safety Information Before you Install the Avaya P460Power Supplies Conventions Used in the Documentation FCC NoticeAvaya Support WarrantyCLI Conventions Preface Avaya P460 Installation and Maintenance Guide Introduction Avaya P460 OverviewManagement and Monitoring Avaya P460 Key FeaturesHigh Availability FlexibilityOperating Safety Avaya P460 Chassis and Module InstallationEnvironmental Prerequisites Required ToolsAC Power Requirements Key Chassis Component LocationRack Mounting Installing the P460 on a Table Top140 mm Positioning the rack-mounting brackets P460 Rack mounting procedureInstalling the Cable Guide Cable Guide InstallationPSU Power Supply Unit Installation Avaya P460 Switch Fan Module Location Fan Module Replacement or InstallationInstalling the Avaya P460 Fan Module Location of the Avaya P460 Supervisor Modules Supervisor Module InstallationInstalling the P460 Supervisor Module 10 Lcoation of Avaya P460 I/O Modules Module Installation11 I/O Module Component Location Module Installation Procedure12 Installing P460 I/O Modules Turning on the Avaya P460 Installing a PSUTurning on a Chassis with no Modules Powering UpInserting an Additional PSU Turning on a Chassis with a Supervisor Module OnlyIf there is one PSU Removing or Switching off a PSUIf there are two PSUs If there are three PSUs Power Management Process Power ManagementI/O Module Power Management Process M460ML-SPV Panel Avaya P460 PanelsM460ML-SPV LEDs PWR ACT LED and OPR LED Summary Function LEDs Starting Point After Power-up or ResetLNK LAG RS-232 Port Sideband Connection M460ML-SPV Supervisor Module PortsM460ML-SPV Left and Right Pushbuttons Eth Port Outband ConnectionP460 Supervisor Module ASB Pushbutton M460ML-SPV ASB Alternate Software Bank PushbuttonPower Supply Panel Page M460ML-SPV Supervisor Module Redundancy Maximizing Avaya P460 AvailabilityM460ML-SPV Supervisor Module Modes Synchronizing the Supervisor Modules Manually Following screen capture shows the process Configuration File SynchronizationMaximizing Avaya P460 Availability P460 show environment power Redundant Power SuppliesSample Power Budget Calculation Calculating the Power BudgetEstablishing a Console Connection with the P460 Establishing Switch AccessInband Interface Connection CLI Commands Establishing a Telnet Connection with the Switch InbandM460ML-SPV Supervisor Module Fast Ethernet Console Port Establishing a Telnet Connection with the Switch OutbandOutband Interface Connection CLI Commands Redundant Outband Connections Redundant Outband ConnectionsOverview Sideband PPP Interface CLI CommandsSet interface ppp ipaddrnet-mask Setting Up Sideband PPP Connection ConfigurationPage Avaya Msnm P460 Manager Welcome Running the Avaya Msnm P460 ManagerP460 Device Manager Install from your Local Web Site Installing the Java Plug-inInstalling from the P460 Documentation and Utilities CD Install from the Avaya Web SiteDocumentation Page Access Levels User AuthenticationLocal User Accounts Local User Account CLI Commands Introduction to Radius RadiusRadius CLI Commands Illustrates the Radius authentication procedureUser Authentication Allowed Managers Allowed Manager CLI CommandsDefault System Parameters Configuration DefaultsConfiguration Default CLI Commands Basic Switch Configuration Identifying the system System Parameter ConfigurationOperating parameters Feature License Configuration Time Parameter ConfigurationFeature Activation Obtaining a License Key Click Generate Activating a Routing License Key Feature License CLI CommandsPowering up the Fan Module Troubleshooting the InstallationPowering up the Chassis Powering up the Supervisor ModulesPowering up the I/O Modules Supervisor Module does not Boot Page Replacing I/O Modules MaintenanceOne Supervisor Module in the Switch Two Supervisor Modules in the SwitchIntroduction Firmware DownloadPreferred Bank Firmware Download CLI Commands Configuration File ManagementConfiguration Management CLI Commands Page Ieee StandardsRouting Physical SpecificationsSafety Power RequirementsEnvironmental Immunity EMC EmissionsTransportation Avaya P460 Catalog Numbers Catalog Numbers