Runco dtv-992/992 ultra Control panel terminology, Local Keypad, RCU control panel terminology

Page 10

LOCATION AND FUNCTION OF CONTROLS

Control panel terminology

a. The Local Keypad

Getting Access

The local keypad is underneath the top cover door with the Runco logo.

To open this door, push as indicated on drawing and turn it to the front side of the projector.

This local keyboard has the same functions as the Remote Control Unit (RCU)

b. RCU control panel terminology

This remote control includes a battery powered infrared (IR) trans- mitter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set-up. It includes automatic storing of

picture controls (Brightness, Sharpness )

–picture geometry adjustments

–convergence adjustments

Other functions of the remote control are:

–switching between standby and operational modes

–switching to “pause” (blanked picture, full power for immediate restarting)

–direct access to all connected sources

–variable adjustment speed : when pushing continuously on the control stick or the picture keys, the adjustment will be executed in an accelerated fashion.

2-2

Image 10

Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APX-6 APP-3EYE-QTMDIAGNOSTICS Safety Instructions Installation InstructionsSafety Instructions Rear Panel Terminology Location and Function of ControlsFront Panel Terminology Local Keypad Control panel terminologyRCU control panel terminology IR Transmission Indicator Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsStart up with full white image Signal Input Connection to the ProjectorPort No Projector Input Press Digit Button Rgbs or RGsB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection Remote controlData communications Battery installation in the RCU ControllingHow to display a projector address? How to use your RCUUsing your RCU Hardware set up of the projector addressGeneral Access Menu Items Source Input selectionAnalog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeStart Up of the Adjustment Mode Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch PatternSync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalancePress Enter to display the color select menu PeakingColor Select Display the projected image in that specific colorFocusing FocusingPhase Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WLeft Side Correction Left Side Correction Left Keystone Left BOWTop-Bottom north-south Adjustments TOP Bottom N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Adjustments Blanking TOP Bottom Left RightCoarse Convergence Adjustments Convergence AdjustmentConvergence Fine Convergence Adjustments Vertical cornersStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Identification IdentificationCopy a block Copy a BlockDelete a Block Deletion of blocksDeleting block by block Delete ALL BlocksChange Language Change passwordTotal Run Time Convergence mid All settings to midpositionUndo all settings to midpos Undo R & B convergence midDynamic Astigmatism spot shape adjustment Arrow key Axial Astigmatism correctionCRT run in cycle G2 AdjustmentCommon Settings 12C Diagnostics CRT RUN in Cycle Projector Warm UPProjector warm up Projector Warm UPMESSAGES, WARNINGS, and Failures SourceFailure DTV-992 DTV-992 UltraAppendix RS 232 ControlSending a Record single instruction Decimal values STXSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewCompact, built-in system Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Preparing your EYE-QTMAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyCentering the Camera Vertically TOUCH-UP on Source ON/OFFAdjusting Other Sources TOUCH-UP on TimerReference Source What is Being Measured by EYE-QTM Learning a ReferenceAdjusting Screen Size On Current SourceAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev