Runco runco super hdtv dtv video projector manual MESSAGES, WARNINGS, and Failures, Source

Page 45

MESSAGES, WARNINGS, AND FAILURES

8

SOURCE 01

Fh= 15.6 kHz

Fv= 050 Hz

When selecting a new source,	WARNING:
information about this source will be	WARNING:
displayed on the screen. Source	source not available
number, horizontal and vertical
frequencies of the displayed source.

The input is a valid input but the source is not connected to the input terminals or the input source is switched off.

SOURCE 01

Fh= 15.6 kHz

Fv= 050 Hz

enter password

xxxx

text on

Announcement of the selected source.

Message to enter your password.

Password contains 4 digits.

These messages will be displayed on the screen when pushing the

<TEXT> key.

Text ON : the `bar scale indication' will be enabled during the change of an analog control in the `operational mode'+all warnings and failures will be displayed.

WARNING:

invalid key entry

WARNING:

invalid

code entry

WARNING:

end of adjust range

When a wrong key is pressed on the RCU.

Message when the entered pass word is wrong.

End of adjustment range.

text off

PROJECTOR

ADDRESS:

003

Text OFF : the `barnacle indication' will be disabled during the change of an analog control in the `operational mode'sall warnings and failures will not be displayed.

Indication of the projector ad dress when activating the `AD DRESS' button on the RCU with a pencil or other small object.

WARNING:

input no longer

available

check input signal

or select

new source

Message will be displayed when the input source is no longer available. The following message then appears: `check input signal or select new source'.

This message will be displayed after the message `input no longer available'It. asks to check the connections between the source and the projector or to check if the source is switched on.

8-1

Image 45

Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APP-3 APX-6EYE-QTMDIAGNOSTICS Installation Instructions Safety InstructionsSafety Instructions Location and Function of Controls Rear Panel TerminologyFront Panel Terminology Control panel terminology Local KeypadRCU control panel terminology IR Transmission Indicator Power Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsSignal Input Connection to the Projector Start up with full white imagePort No Projector Input Press Digit Button Connecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection Remote control YYB-Y3S or R-YY3sB-Y input selectionData communications Controlling Battery installation in the RCUUsing your RCU How to use your RCUHow to display a projector address? Hardware set up of the projector addressInput selection General Access Menu Items SourcePause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalanceColor Select PeakingPress Enter to display the color select menu Display the projected image in that specific colorFocusing FocusingHorizontal Phase Adjustment Geometry AdjustmentsPhase GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsLeft Side Correction Left Keystone Left BOW Left Side CorrectionTOP Bottom N-S Top-Bottom north-south AdjustmentsSize Adjustment Vertical Linearity AdjustmentLinearity Blanking TOP Bottom Left Right Blanking AdjustmentsConvergence Adjustment Coarse Convergence AdjustmentsConvergence Vertical corners Fine Convergence AdjustmentsService Mode Starting up the Service modeOverview flowchart ‘Service’ mode Copy a block IdentificationIdentification Copy a BlockDeleting block by block Deletion of blocksDelete a Block Delete ALL BlocksChange password Change LanguageTotal Run Time Undo all settings to midpos All settings to midpositionConvergence mid Undo R & B convergence midArrow key Axial Astigmatism correction Dynamic Astigmatism spot shape adjustmentCommon Settings 12C Diagnostics G2 AdjustmentCRT run in cycle CRT RUN in Cycle Projector Warm UPProjector Warm UP Projector warm upSource MESSAGES, WARNINGS, and FailuresFailure DTV-992 Ultra DTV-992RS 232 Control AppendixSending a Record single instruction STX Decimal values$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic geometry system Easy-to-use, high precision automatic convergence systemCompact, built-in system Preparing your EYE-QTMEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusSetting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyTOUCH-UP on Timer Adjusting Other SourcesReference Source Learning a Reference What is Being Measured by EYE-QTMOn Current Source Adjusting Screen SizeTOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev