Runco dtv-992/992 ultra manual Identification, Copy a block, Copy a Block

Page 38

Service Mode

Identification

Highlight ‘Identification’ with the control disc and press ENTER.

ENTER will start the selected item.

EXIT returns to the Service mode menu.

The ‘Identification’ screen gives information concerning :

-Projector address. To change the address of your projector, contact a qualified service technician.

-Software version.

-Configuration.

Possible installations :

*Front-ceiling

*Front-table

*Rear-ceiling

*Rear-table

-Baud rate PC : transfer speed for communication with an IBM PC (or compatible) or MAC. The baud rate of the projector must be the same as the baud rate of the connected computer. When there is a differ- ence, contact a qualified service technician to make the appropriate changes.

-Text ON/OFF

Indicates in operational mode if the bar scale and number indicator will be displayed and if warnings and failures will be displayed.

ON : displayed

OFF : not displayed

The status can be changed by pressing the ‘TEXT’ key once on the RCU.

-Serial no. : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.

Copy a block

The copy a block function copies the settings of a selected block into the active block.

Highlight copy a block with the control disc and press ENTER.

ENTER will select the highlighted item.

EXIT returns to the Path Selection main menu.

ADJUST returns to the Operational mode.

To copy the settings of a closed block to the block you are working on (active block), use the control disc to select a block.

All existing settings will be overwritten with the new settings.

Press ENTER to copy the selected block. A confirmation screen will be displayed.

If you are certain you wish to copy the contents of the selected block into the active block, press ENTER.

ENTER displays a confirmation screen.

EXIT returns to the Service Mode main menu.

EXIT cancels the copy procedure and returns without copying the block.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

POWER UP MODE: operating

RUNCO

DTV - 992

Proj. address : 001

Soft. Version : 6.00

Config. :Ceiling

Front

Baudrate PC : 9600

Text : ON

Serial No. : 103589552

MEMORY MANAGEMENT

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

ALL SETTINGS TO MIDPOS

 

 

COPY MODE

 

Nr.

Src

Fh

Fv

inp

conf

1

1

15.6 50

video

FC

 

 

 

COPY BLOCK

 

All settings

 

 

 

in current block

 

 

will be overwritten !

 

Select with or then <ENTER> <EXIT> to return.

7-2

Page 37 Page 39
Image 38
Page 37 Page 39
Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APX-6 APP-3EYE-QTMDIAGNOSTICS Safety Instructions Installation InstructionsSafety Instructions Front Panel Terminology Location and Function of ControlsRear Panel Terminology RCU control panel terminology Control panel terminologyLocal Keypad IR Transmission Indicator Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsPort No Projector Input Press Digit Button Signal Input Connection to the ProjectorStart up with full white image Rgbs or RGsB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selectionYYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync Data communications Remote controlYYB-Y3S or R-YY3sB-Y input selection Battery installation in the RCU ControllingHow to display a projector address? How to use your RCUUsing your RCU Hardware set up of the projector addressGeneral Access Menu Items Source Input selectionAnalog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeStart Up of the Adjustment Mode Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Selecting Setup Pattern Internal Cross Hatch PatternSync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalancePress Enter to display the color select menu PeakingColor Select Display the projected image in that specific colorFocusing FocusingPhase Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WLeft Side Correction Left Side Correction Left Keystone Left BOWTop-Bottom north-south Adjustments TOP Bottom N-SLinearity Size AdjustmentVertical Linearity Adjustment Blanking Adjustments Blanking TOP Bottom Left RightConvergence Convergence AdjustmentCoarse Convergence Adjustments Fine Convergence Adjustments Vertical cornersOverview flowchart ‘Service’ mode Service ModeStarting up the Service mode Identification IdentificationCopy a block Copy a BlockDelete a Block Deletion of blocksDeleting block by block Delete ALL BlocksTotal Run Time Change passwordChange Language Convergence mid All settings to midpositionUndo all settings to midpos Undo R & B convergence midDynamic Astigmatism spot shape adjustment Arrow key Axial Astigmatism correctionCRT run in cycle G2 AdjustmentCommon Settings 12C Diagnostics CRT RUN in Cycle Projector Warm UPProjector warm up Projector Warm UPMESSAGES, WARNINGS, and Failures SourceFailure DTV-992 DTV-992 UltraAppendix RS 232 ControlSending a Record single instruction Decimal values STXSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewCompact, built-in system Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Preparing your EYE-QTMAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyCentering the Camera Vertically TOUCH-UP on Source ON/OFFReference Source TOUCH-UP on TimerAdjusting Other Sources What is Being Measured by EYE-QTM Learning a ReferenceAdjusting Screen Size On Current SourceAlign from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev
Top Page Image Contents