Runco dtv-992/992 ultra manual Connecting a RGB Analog source with composite sync

Page 14

Connections

Connecting a RGB Analog source with composite sync.

RGB analog input terminals with composite sync input or with sync on green. The projector detects automatically where the sync signal is located.

Always use an interface when a computer and local mon- itor have to be connected to the projector. Examples of interfaces which can be applied :

RGBS or RGsB input selection

a. With the RCU: Select RGB in the Source Selection menu

b. With the local keypad :

(to gain access to the local keypad, see ‘Local key- pad’ in chapter “Location and function of controls’.)

-Press ADJUST key, the General access menu is displayed on the screen.

-Use the control disk to highlight 3.

-Press ENTER to select the highlighted source.

Connecting a RGB Analog source with Tri-level sync.

RGB analog input terminals with Tri level sync input or with Tri-level sync on green. The projector detects auto- matically where the sync signal is located.

RGB3S or RG3sB input selection

a. With the RCU: Select RGB in the Source Selection menu

b. With the local keypad :

(to gain access to the local keypad, see ‘Local key- pad’ in chapter ‘Location and function of controls’.) -Press ADJUST key, the General access menu is displayed on the screen.

-Use the control disk to highlight 4.

-Press ENTER to select the highlighted source.

This device complies with part 15 of the FCC rules. Operation is subject to following two conditions (1). This device may not cause harmful inter- ference, and (2) this device must accept any interference received including interference that may cause undesired operation.

ON	ANALOG INTERF 120 MHz INPUT		H	V
		B	H	V
OFF	R	G	INP	INP

This device complies with part 15 of the FCC rules. Operation is subject to following two conditions (1). This device may not cause harmful inter- ference, and (2) this device must accept any interference received including interference that may cause undesired operation.

ON	ANALOG INTERF 120 MHz INPUT		H	V
		B	H	V
OFF	R	G	INP	INP

3-3

Image 14

Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APX-6 APP-3EYE-QTMDIAGNOSTICS Safety Instructions Installation InstructionsSafety Instructions Front Panel Terminology Location and Function of ControlsRear Panel Terminology RCU control panel terminology Control panel terminologyLocal Keypad IR Transmission Indicator Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsPort No Projector Input Press Digit Button Signal Input Connection to the ProjectorStart up with full white image Rgbs or RGsB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selectionYYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync Data communications Remote controlYYB-Y3S or R-YY3sB-Y input selection Battery installation in the RCU ControllingHow to display a projector address? How to use your RCUUsing your RCU Hardware set up of the projector addressGeneral Access Menu Items Source Input selectionAnalog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeStart Up of the Adjustment Mode Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Selecting Setup Pattern Internal Cross Hatch PatternSync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalancePress Enter to display the color select menu PeakingColor Select Display the projected image in that specific colorFocusing FocusingPhase Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WLeft Side Correction Left Side Correction Left Keystone Left BOWTop-Bottom north-south Adjustments TOP Bottom N-SLinearity Size AdjustmentVertical Linearity Adjustment Blanking Adjustments Blanking TOP Bottom Left RightConvergence Convergence AdjustmentCoarse Convergence Adjustments Fine Convergence Adjustments Vertical cornersOverview flowchart ‘Service’ mode Service ModeStarting up the Service mode Identification IdentificationCopy a block Copy a BlockDelete a Block Deletion of blocksDeleting block by block Delete ALL BlocksTotal Run Time Change passwordChange Language Convergence mid All settings to midpositionUndo all settings to midpos Undo R & B convergence midDynamic Astigmatism spot shape adjustment Arrow key Axial Astigmatism correctionCRT run in cycle G2 AdjustmentCommon Settings 12C Diagnostics CRT RUN in Cycle Projector Warm UPProjector warm up Projector Warm UPMESSAGES, WARNINGS, and Failures SourceFailure DTV-992 DTV-992 UltraAppendix RS 232 ControlSending a Record single instruction Decimal values STXSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewCompact, built-in system Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Preparing your EYE-QTMAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyCentering the Camera Vertically TOUCH-UP on Source ON/OFFReference Source TOUCH-UP on TimerAdjusting Other Sources What is Being Measured by EYE-QTM Learning a ReferenceAdjusting Screen Size On Current SourceAlign from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev