Runco runco super hdtv dtv video projector manual Adjusting Screen Size, On Current Source

Page 61

Appendix 2

TOUCH UP AND AUTOCONVERGENCE

ADJUSTING SCREEN SIZE

In case the projection screen is not greater than the desired size or the screen has a frame around it (i.e. projection impossible outside the frame), the following blanking adjust- ments have to be done before starting the automatic con- vergence:

When using a video source: adjust the top, bottom, left and right blanking until the whole projected image of video is just still visible;

When using a screen with a frame: adjust the top, bot- tom, left and right blanking until the whole projected image is just still visible.

So that the selected screen area after blanking adjustments corresponds with the projected image size.

In this way, the screen size is set correctly to ensure the suc- cessful convergence.

Left	Top
blanking	blanking
Bottom	Right
blanking	blanking

NOTE:

For blanking adjustments, please refer to the Projector Setup Manual.

To enter the AUTOCONVERGENCE menu:

Highlight AUTOCONVERGENCE by pushing up or down keys of the control disc;

Press the <ENTER> button.

The AUTOCONVERGENCE menu allows the automatic convergence either on the currently selected source or on all sources (all filled memory blocks of the projector).

ON CURRENT SOURCE

the on current source includes three options, the first of which is selectable in the iris menu:

Touch Up EYE-QTM

Align

Align from midposition

ADJUSTMENT MODE

Select a path from below:

EYE-Q

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

Source 1

EYE-Q
TOUCH UP
AUTOCONVERGENCE
QUICK AUTOPICTURE
FULL AUTOPICTURE
EYE-Q SETUP
EYE-Q DIAGNOSTICS
AUTOCONVERGENCE
ON CURRENT SOURCE:
ALIGN
ALIGN FROM MIDPOSITION
ON ALL SOURCES: (XX)
TOUCH-UP
ALIGN
ALIGN FROM MIDPOSITION
STATUS:
ready
Select with	or
then <ENTER>.
<EXIT> to return

APX-10

Image 61

Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APP-3 APX-6EYE-QTMDIAGNOSTICS Installation Instructions Safety InstructionsSafety Instructions Rear Panel Terminology Location and Function of ControlsFront Panel Terminology Local Keypad Control panel terminologyRCU control panel terminology IR Transmission Indicator Power Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsStart up with full white image Signal Input Connection to the ProjectorPort No Projector Input Press Digit Button Connecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection Remote controlData communications Controlling Battery installation in the RCUUsing your RCU How to use your RCUHow to display a projector address? Hardware set up of the projector addressInput selection General Access Menu Items SourcePause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalanceColor Select PeakingPress Enter to display the color select menu Display the projected image in that specific colorFocusing FocusingHorizontal Phase Adjustment Geometry AdjustmentsPhase GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsLeft Side Correction Left Keystone Left BOW Left Side CorrectionTOP Bottom N-S Top-Bottom north-south AdjustmentsVertical Linearity Adjustment Size AdjustmentLinearity Blanking TOP Bottom Left Right Blanking AdjustmentsCoarse Convergence Adjustments Convergence AdjustmentConvergence Vertical corners Fine Convergence AdjustmentsStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Copy a block IdentificationIdentification Copy a BlockDeleting block by block Deletion of blocksDelete a Block Delete ALL BlocksChange Language Change passwordTotal Run Time Undo all settings to midpos All settings to midpositionConvergence mid Undo R & B convergence midArrow key Axial Astigmatism correction Dynamic Astigmatism spot shape adjustmentCommon Settings 12C Diagnostics G2 AdjustmentCRT run in cycle CRT RUN in Cycle Projector Warm UPProjector Warm UP Projector warm upSource MESSAGES, WARNINGS, and FailuresFailure DTV-992 Ultra DTV-992RS 232 Control AppendixSending a Record single instruction STX Decimal values$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic geometry system Easy-to-use, high precision automatic convergence systemCompact, built-in system Preparing your EYE-QTMEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusSetting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAdjusting Other Sources TOUCH-UP on TimerReference Source Learning a Reference What is Being Measured by EYE-QTMOn Current Source Adjusting Screen SizeAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev