Runco runco super hdtv dtv video projector, dtv-992/992 ultra manual IR Transmission Indicator

Page 11

LOCATION AND FUNCTION OF CONTROLS

1

18			17		16

F5

EXIT

F4

F3

F2

F1

ADJ

2

		14			12


15			13				11

ENT

ll

TEXT

- PHASE +

*
PAUSE	?



3			4				6
						5
						5

10

- SHARPN +	- TINT +	- COLOR +	- BRIGHTN +	- CONTR +	BALANCE +	- VOL +
					-
0	8	6	4	2	TREBLE +	- BASS +
9	7	5	3	1	-
9	7	5	3	1




7		8					9

1IR Transmission Indicator

2ADJ. : Adjust key, to enter or exit the adjustment mode.

3Address key (recessed key) : to enter the address of the projec- tor (between 0 and 9). Press the address key, followed by press- ing one digit button between 0 and 9. When addressed to O , the remote will talk to any projector, regardless of its address.

4STBY : Stand by button:

-To initiate remote power up operation

-To stop projection without main power off.

5Pause : To mute the image, press PAUSE. The image disappears but full power is retained for immediate restarting.

6Mute : Not used

7Help : Not used.

8Digit buttons : Direct aspect ratio selection.

9Sound controls : Not used.

10Picture controls : Use these buttons to obtain the desired level (see also ‘Controlling’) for each picture function.

11Phase : Not used.

12Text : When adjusting one of the image controls during a meet- ing, the displayed bar scale can be removed by pressing ‘TEXT’ key first. To re-display the bar scale on the screen, press ‘TEXT’ key again. ‘TEXT’ key is only active in operational mode. When ‘TEXT’ is off, no warning message will be dis

played.

13FREEZ : Not used.

stand-bycolor

pause / park	brightness
sharpness	contrast

tint

14For Future Use

15ENTER : To start up the adjustment mode or to confirm an adjustment or selection in the adjustment mode.

16Control disc : To make menu selections when in the adjustment mode. Also allows to increment or decrement an adjustment in

the adjustment mode.

Control disc up = up arrow in the menus Control disc down = down arrow in the menus

Control disc to the right = arrow to the right on the menus Control disc to the left = arrow to the left on the menus

17EXIT : To leave the adjustment mode or to scroll upwards when in the adjustment mode.

18For Future Use

2-3

Image 11

Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APP-3 APX-6EYE-QTMDIAGNOSTICS Installation Instructions Safety InstructionsSafety Instructions Front Panel Terminology Location and Function of ControlsRear Panel Terminology RCU control panel terminology Control panel terminologyLocal Keypad IR Transmission Indicator Connections AC Power mains Cord ConnectionPower Check Switching On/OffPort No Projector Input Press Digit Button Signal Input Connection to the ProjectorStart up with full white image RGB3S or RG3sB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync Rgbs or RGsB input selectionYYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync Data communications Remote controlYYB-Y3S or R-YY3sB-Y input selection Controlling Battery installation in the RCUHardware set up of the projector address How to use your RCUUsing your RCU How to display a projector address?Input selection General Access Menu Items SourcePause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentDisplay the projected image in that specific color PeakingColor Select Press Enter to display the color select menuFocusing FocusingGeometry Geometry AdjustmentsHorizontal Phase Adjustment PhaseRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsLeft Side Correction Left Keystone Left BOW Left Side CorrectionTOP Bottom N-S Top-Bottom north-south AdjustmentsLinearity Size AdjustmentVertical Linearity Adjustment Blanking TOP Bottom Left Right Blanking AdjustmentsConvergence Convergence AdjustmentCoarse Convergence Adjustments Vertical corners Fine Convergence AdjustmentsOverview flowchart ‘Service’ mode Service ModeStarting up the Service mode Copy a Block IdentificationCopy a block IdentificationDelete ALL Blocks Deletion of blocksDeleting block by block Delete a BlockTotal Run Time Change passwordChange Language Undo R & B convergence mid All settings to midpositionUndo all settings to midpos Convergence midArrow key Axial Astigmatism correction Dynamic Astigmatism spot shape adjustmentCRT RUN in Cycle Projector Warm UP G2 AdjustmentCommon Settings 12C Diagnostics CRT run in cycleProjector Warm UP Projector warm upSource MESSAGES, WARNINGS, and FailuresFailure DTV-992 Ultra DTV-992RS 232 Control AppendixSending a Record single instruction STX Decimal values$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemPreparing your EYE-QTM Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Compact, built-in systemEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusSetting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyReference Source TOUCH-UP on TimerAdjusting Other Sources Learning a Reference What is Being Measured by EYE-QTMOn Current Source Adjusting Screen SizeAlign from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev