Runco runco super hdtv dtv video projector, dtv-992/992 ultra Coarse Convergence Adjustments

Page 35

Random Access Adjustment Mode

Convergence Adjustment

Convergence adjustments affect both the horizontal and vertical lines of the setup pattern. These adjustments are performed on the red image while superimposed on the green image and then on the blue image while super- imposed on the green image.

Start with the coarse convergence adjustments and finalize with the fine convergence adjustment.

RANDOM ACESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

COLOR SELECT

SOFT EDGE

CONVERGENCE

GREEN ONLY

RED ON GREEN

BLUE ON GREEN

Select with or then <ENTER> <EXIT> to return

The screen area is divided into 25 areas.

Coarse Convergence Adjustments

Highlight ‘Red on Green’ under the coarse convergence item and press ENTER. The coarse convergence menu will be displayed.

The following items are possible:

*Horizontal sides: adjust the vertical lines, within a certain area, on both sides without influencing the lines on the middle of the image.

*Vertical corners: adjust the horizontal lines in the four corners, within a certain area, without influencing the middle of the image.

Repeat for ‘blue on green’

Horizontal sides

Highlight “Horizontal lines’ and press ENTER to start the adjustment. To make a coarse adjustment of the red or blue vertical lines in ZONE 3 and 5 simultaneously.

B G R B G R

Hint

*Look to the outside edges of the image and adjust until the red or the blue vertical lines are on the green lines or as close as possible to the green lines.

*During these adjustments, the horizontal convergence adjustments in ZONES 2, 3, 4, and 5 will be set to midposition (barscale 50)

25	23	9	15	17

24	22	8	14	16

5	4	1	2	3

20	18	6	10	12

21	19	7	11	13

CONVERGENCE

COARSE ADJUSTMENT

RED ON GREEN

BLUE ON GREEN

CONVERGENCE

HORIZONTAL SIDES

VERTICAL CORNERS

Select with or then <ENTER> <EXIT> to return

CONVERGENCE

COARSE ADJUSTMENT

RED ON GREEN

BLUE ON GREEN

FINE ADJUSTMENT

GREEN ONLY

RED ON GREEN

BLUE ON GREEN

6-13

Image 35

Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APP-3 APX-6EYE-QTMDIAGNOSTICS Installation Instructions Safety InstructionsSafety Instructions Front Panel Terminology Location and Function of ControlsRear Panel Terminology RCU control panel terminology Control panel terminologyLocal Keypad IR Transmission Indicator Connections AC Power mains Cord ConnectionPower Check Switching On/OffPort No Projector Input Press Digit Button Signal Input Connection to the ProjectorStart up with full white image RGB3S or RG3sB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync Rgbs or RGsB input selectionYYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync Data communications Remote controlYYB-Y3S or R-YY3sB-Y input selection Controlling Battery installation in the RCUHardware set up of the projector address How to use your RCUUsing your RCU How to display a projector address?Input selection General Access Menu Items SourcePause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentDisplay the projected image in that specific color PeakingColor Select Press Enter to display the color select menuFocusing FocusingGeometry Geometry AdjustmentsHorizontal Phase Adjustment PhaseRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsLeft Side Correction Left Keystone Left BOW Left Side CorrectionTOP Bottom N-S Top-Bottom north-south AdjustmentsLinearity Size AdjustmentVertical Linearity Adjustment Blanking TOP Bottom Left Right Blanking AdjustmentsConvergence Convergence AdjustmentCoarse Convergence Adjustments Vertical corners Fine Convergence AdjustmentsOverview flowchart ‘Service’ mode Service ModeStarting up the Service mode Copy a Block IdentificationCopy a block IdentificationDelete ALL Blocks Deletion of blocksDeleting block by block Delete a BlockTotal Run Time Change passwordChange Language Undo R & B convergence mid All settings to midpositionUndo all settings to midpos Convergence midArrow key Axial Astigmatism correction Dynamic Astigmatism spot shape adjustmentCRT RUN in Cycle Projector Warm UP G2 AdjustmentCommon Settings 12C Diagnostics CRT run in cycleProjector Warm UP Projector warm upSource MESSAGES, WARNINGS, and FailuresFailure DTV-992 Ultra DTV-992RS 232 Control AppendixSending a Record single instruction STX Decimal values$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemPreparing your EYE-QTM Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Compact, built-in systemEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusSetting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyReference Source TOUCH-UP on TimerAdjusting Other Sources Learning a Reference What is Being Measured by EYE-QTMOn Current Source Adjusting Screen SizeAlign from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev