Runco runco super hdtv dtv video projector, dtv-992/992 ultra Location and Function of Controls

Page 9

2	LOCATION AND FUNCTION OF CONTROLS

This device complies with part 15 of the FCC rules. Operation is subject to following two conditions (1). This device may not cause harmful inter- ference, and (2) this device must accept any interference received including interference that may cause undesired operation.

Comm Port	Port 3	R	G	B Comp/ VSYNC	VIDEO	Green=Oper.
Off On				HSYNC		Red=Stby
Power/Mains

1

2

3

4

5

6

7

8

9

10

REAR PANEL TERMINOLOGY

1Power Switch: press the switch to turn the projector ON.

Depending on the hardware set-up of the projector during installation, the projector switches to ‘Standby’ or to ‘Opera- tional’ mode. If in standby, the standby LED lights up.

2AC Power Input

3Communication Port

•allows connection of a remote IR receiver unit to the projector.

4Port 3

RGB Analog Input (9 pin female sub D connector). Allows a character generator, microcomputer, etc. having analog RGB outputs to be connected to the projector.

5Port 4/5: RGB-S Input (5x BNC connector):

RGB-S input: allows a character generator, microcomputer, video camera, etc. having analog RGB Output to be con- nected to the projector.

Line inputs

– signals RED-GREEN-BLUE

– COMPOSITE sync. signal

– Tri level sync. signal (option>)

6S-VIDEO Input: (Not Active)

775 ohm Termination Switch for S-Video signals

8VIDEO Input: (Not Active)

975 ohm Termination Switch for Video signals: (Not Active)

10Projector Pilot Lamp: indicates the Status of the projector.

–unlit: mains (power) switch is not pressed.

–lit: mains (power) switch is pressed and the indicated color shows the projector mode: Green color : operational mode of the projector. Red color: standby mode of the projector.

			NS	8m
			LE	m
RS232 IN	RS232 OUT	IR REMOTE	V
RS232 IN	RS232 OUT	IR REMOTE	T
			T	m
			V	m
				8m
			LE NS
IN RS232	OUT RS232	IR REMOTE

11

12

13

14

15

FRONT PANEL TERMINOLOGY

11RS 232 Input Port

Connection between the DTV-992 / 992 ULTRA and an IBM PC (or compatible) Or MAC (RS422) for remote computer control and data communication.

12RS 232 Output Port

RS232 Input Port allows a communication link for PC 0r MAC to the next projector in a series of projector.

13IR Sensor

receiver for control signals transmitted from the RCU.

14IR Remote

Connector for remote input for hard wired remote Control.

15EYE-Q Camera

2-1

Image 9

Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APP-3 APX-6EYE-QTMDIAGNOSTICS Installation Instructions Safety InstructionsSafety Instructions Location and Function of Controls Rear Panel TerminologyFront Panel Terminology Control panel terminology Local KeypadRCU control panel terminology IR Transmission Indicator Power Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsSignal Input Connection to the Projector Start up with full white imagePort No Projector Input Press Digit Button Connecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection Remote control YYB-Y3S or R-YY3sB-Y input selectionData communications Controlling Battery installation in the RCUUsing your RCU How to use your RCUHow to display a projector address? Hardware set up of the projector addressInput selection General Access Menu Items SourcePause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalanceColor Select PeakingPress Enter to display the color select menu Display the projected image in that specific colorFocusing FocusingHorizontal Phase Adjustment Geometry AdjustmentsPhase GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsLeft Side Correction Left Keystone Left BOW Left Side CorrectionTOP Bottom N-S Top-Bottom north-south AdjustmentsSize Adjustment Vertical Linearity AdjustmentLinearity Blanking TOP Bottom Left Right Blanking AdjustmentsConvergence Adjustment Coarse Convergence AdjustmentsConvergence Vertical corners Fine Convergence AdjustmentsService Mode Starting up the Service modeOverview flowchart ‘Service’ mode Copy a block IdentificationIdentification Copy a BlockDeleting block by block Deletion of blocksDelete a Block Delete ALL BlocksChange password Change LanguageTotal Run Time Undo all settings to midpos All settings to midpositionConvergence mid Undo R & B convergence midArrow key Axial Astigmatism correction Dynamic Astigmatism spot shape adjustmentCommon Settings 12C Diagnostics G2 AdjustmentCRT run in cycle CRT RUN in Cycle Projector Warm UPProjector Warm UP Projector warm upSource MESSAGES, WARNINGS, and FailuresFailure DTV-992 Ultra DTV-992RS 232 Control AppendixSending a Record single instruction STX Decimal values$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic geometry system Easy-to-use, high precision automatic convergence systemCompact, built-in system Preparing your EYE-QTMEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusSetting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyTOUCH-UP on Timer Adjusting Other SourcesReference Source Learning a Reference What is Being Measured by EYE-QTMOn Current Source Adjusting Screen SizeTOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev