Runco runco super hdtv dtv video projector manual Random access adjustment mode selection menu

Page 25

Random Access Adjustment Mode

Random access adjustment mode selection menu

This is the main menu for the Random Access adjustment mode. Through this menu, the following adjustments and features are accessible:

-Picture Tuning

Sync slow/fast (video/s-video) Color Balance

-Geometry Convergence

-Color Select

And also Orbiting, Contrast modulation and Soft Edge, if these options are installed.

Picture Tuning

Highlight Picture tuning by pushing the control disc up or down and press

ENTER.

The Picture tuning menu will be displayed.

Depending on the input source, the ‘Picture tuning’ menu will display differ- ent items.

-Color Balance

-Sync slow/fast

-Peaking

Color Balance

The Color Balance function is used to select or adjust the color temperature of white used by the projector.

The Color Balance can be adjusted in two different ways:

-fixed color balance. You have the choice between 3200k (reddish), 5400 K, 6500 K (white), or 9300 K (bluish).

-Custom white and black balance.

Fixed Color Balance

Highlight one of the 4 programmed color temperatures with the control disc and press ENTER to display the desired color balance.

Custom Color Balance

Select custom white balance by pushing the control disc up or down and press ENTER to start the adjustment.

Push the control disc up or down to adjust the red gain and push the control disc to the left or right to adjust the blue gain. A bar scale indicates the amount of adjustment.

Select custom black balance with the control disc and press ENTER to start the adjustment.

Push the control disc up or down to adjust the red cut-off and push the con- trol disc to the left or to the right to adjust the blue cut-off.

When the color balance is adjusted, select continue by pushing the control disc up or down and press ENTER.

Sync Fast/Slow Adjustment

The sync function is used to minimize horizontal jittering or tearing at the top to the displayed image.

Highlight SYNC with the control disc and press ENTER to toggle between FAST and SLOW.

Note: SYNC is normally used in the SLOW position. The FAST position is used to compensate for unsteady sync pulses from older video playback equipment, such as a VCR.

ENTER will toggle Sync between FAST and SLOW.

EXIT will return to the Random Access Adjustment menu.

6-3

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

COLOR SELECT

Select with or then <ENTER> <EXIT> to return

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PEAKING : ON

Select with or <ENTER> to accept <EXIT> to return.

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PEAKING : ON

COLOR BALANCE

FIXED COLOR BALANCE

3200 5400 6500 9300

CUSTOM WHITE BALANCE

CUSTOM BLACK BALANCE

Select with arrow keys

then <ENTER>

You can

 

adjust red with

or

Blue with

or

<EXIT> to return

PICTURE TUNING

COLOR BALANCE

SYNC : FAST

PEAKING : ON

Select with or <ENTER> to accept <EXIT> to return.

Page 24 Page 26
Image 25
Page 24 Page 26
Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APP-3 APX-6EYE-QTMDIAGNOSTICS Installation Instructions Safety InstructionsSafety Instructions Rear Panel Terminology Location and Function of ControlsFront Panel Terminology Local Keypad Control panel terminologyRCU control panel terminology IR Transmission Indicator Power Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsStart up with full white image Signal Input Connection to the ProjectorPort No Projector Input Press Digit Button Connecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection Remote controlData communications Controlling Battery installation in the RCUUsing your RCU How to use your RCUHow to display a projector address? Hardware set up of the projector addressInput selection General Access Menu Items SourcePause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalanceColor Select PeakingPress Enter to display the color select menu Display the projected image in that specific colorFocusing FocusingHorizontal Phase Adjustment Geometry AdjustmentsPhase GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsLeft Side Correction Left Keystone Left BOW Left Side CorrectionTOP Bottom N-S Top-Bottom north-south AdjustmentsVertical Linearity Adjustment Size AdjustmentLinearity Blanking TOP Bottom Left Right Blanking AdjustmentsCoarse Convergence Adjustments Convergence AdjustmentConvergence Vertical corners Fine Convergence AdjustmentsStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Copy a block IdentificationIdentification Copy a BlockDeleting block by block Deletion of blocksDelete a Block Delete ALL BlocksChange Language Change passwordTotal Run Time Undo all settings to midpos All settings to midpositionConvergence mid Undo R & B convergence midArrow key Axial Astigmatism correction Dynamic Astigmatism spot shape adjustmentCommon Settings 12C Diagnostics G2 AdjustmentCRT run in cycle CRT RUN in Cycle Projector Warm UPProjector Warm UP Projector warm upSource MESSAGES, WARNINGS, and FailuresFailure DTV-992 Ultra DTV-992RS 232 Control AppendixSending a Record single instruction STX Decimal values$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemEasy-to-use, high precision automatic geometry system Easy-to-use, high precision automatic convergence systemCompact, built-in system Preparing your EYE-QTMEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusSetting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAdjusting Other Sources TOUCH-UP on TimerReference Source Learning a Reference What is Being Measured by EYE-QTMOn Current Source Adjusting Screen SizeAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev
Top Page Image Contents